the all aussie dribble thread!

[460cixy]

Meteor are fine

 

[splitpost]

Thanks Who ?

Everyone calls him the greek ,his ebay store

Sent from my SM-N910G using Tapatalk

 

[peter92]

Everyone calls him the greek ,his ebay storeView attachment 547714View attachment 547715

Sent from my SM-N910G using Tapatalk

thanks for that , very much app it
Peter

 

[460cixy]

That's him but make sure you get a new gudgeon bearing wouldn't put a saw together with out one and check for air leaks un less its been straight fuelled an air leak is all that will bring a a 266 to its knees

 

[peter92]

Everyone calls him the greek ,his ebay storeView attachment 547714View attachment 547715

Sent from my SM-N910G using Tapatalk

whats it cost to get it here all up including purchase

 

[peter92]

That's him but make sure you get a new gudgeon bearing wouldn't put a saw together with out one and check for air leaks un less its been straight fuelled an air leak is all that will bring a a 266 to its knees

yep, it still runs but needs a carby kit , and i thought that kit would of had a bearing , if not i,ll buy one for sure

 

[460cixy]

If it still runs why do you think it needs the top end done

 

[peter92]

If it still runs why do you think it needs the top end done

just in case the comp is down when the saw arrives , havent seen it yet

 

[460cixy]

Wouldn't panic about it if it starts and runs it will be fine. Old huskys are like anvils

 

[peter92]

Wouldn't panic about it if it starts and runs it will be fine. Old huskys are like anvils

just what i like to hear, have read that the 266 , is similar to the 365 in power in small wood , but the 365 is better in larger stuff
dont know how true that is

 

[postmanpatt]

just stick to the stihls end of heart ache!!

 

[peter92]

just stick to the stihls end of heart ache!!

husky,s arent bad , well old ones any way , my 61 was great

 

[postmanpatt]

yes well if they made the 2100cd model again that would be the pic.

 

[peter92]

yes well if they made the 2100cd model again that would be the pic.

ill take the 2100 instead

 

[postmanpatt]

well I had 5 2100cds at one stage but could not get a air filter when my last saw died so sold the lot.huskys to hard to get parts .glad I went to stihls.

 

[460cixy]

well I had 5 2100cds at one stage but could not get a air filter when my last saw died so sold the lot.huskys to hard to get parts .glad I went to stihls.

Lol 40 year old saw and moaning about parts ****in get a grip

 

[derwoodii]

well I had 5 2100cds at one stage but could not get a air filter when my last saw died so sold the lot.huskys to hard to get parts .glad I went to stihls.

welcome post man pat how were your 5, 2100 balanced bit of kit or ? and did you ever plonk oil fuel in the wrong holes i now i could after a bender nite out

 

[postmanpatt]

they were bloodly good saws.they went hard but in our aussie red and grey ironbark it killed them.well I did service them daily but things do wear out.i looked for filters for about 4 years and could not find any.plus pistons and rings no where to be found.it was a case of every one who had these saws was not selling even a bolt of theses saws!so bugger it they went on ebay.

 

[2strokenut]

well the old gutlux hit 300000km on the weekend got a new t-belt and water pump kit coming and well im at it time to replace the original shocks so got a new set on there way as well as spring rubbers.

 

[chippy]

300k for shocks...you've done well. You must drive it like an old granny to get that many k''s out of them.
How are the wheel bearings going?