Chinese cylinders

[TheDarkLordChinChin]

Does margarine taste like butter?

 

[TBS]

 

[dmb2613]

Does margarine taste like butter?

hell butter don't taste like butter any more

 

[svk]

Billy boy, do you read any other posts on here, or just the ones you write?
This little gem is hardly a well kept secret- sharp edges- crappy coating- bad port timing- oval bores...... they all get mentioned pretty regular on here when it comes to any post about AM cylinders from the PRC.

h
He has been here for 2 years and over 5,000 post, what do you think

I’d say that’s a resounding no, as he doesn’t use the search function, ever. LOL

 

[cuinrearview]

Oh no.... I'm not getting dragged into this.

???? I'm sure with some research you could find a Husky rep that says this ****'s the same as the stuff from Sweden.

 

[TBS]

Does margarine taste like butter?

Do bacon covered maple bars taste better than regular maple bars?

 

[TBS]

I’d say that’s a resounding no, as he doesn’t use the search function, ever. LOL

I think bill gets bored.

 

[svk]

I think bill gets bored.

Highly plausible!

 

[Huskybill]

Amish roll butter still tastes like real butter. Yes I do use the search engine.
Am I bored? Not yet.

The meteor piston kits are $130.

 

[cuinrearview]

Yes I do use the search engine.

@Jkstihl could use a lesson on it. Teach him what you've learned Bill.

 

[Huskybill]

Oh no.... I'm not getting dragged into this.

Come on noodlewalker your dragged into this too now. Add your knowledge into this too?

 

[cuinrearview]

Come on noodlewalker your dragged into this too now. Add your knowledge into this too?

He's your guy for sure. He's built over 40 Chaws, all ran great. He builds them 99% or so from Charts.

 

[mike-s]

He meant CHinese cyinlder with INK on top. Very common term here.

No, he didn't. And, if it's very common here, this site is filled with sociopathic reprobates. Sure, lots of Chinese products are cheap crap. But that's no excuse for being an ugly and ignorant American.

 

[cuinrearview]

No, he didn't.

What did he mean then?

 

[TBS]

Bill starts a thread asking about aftermarket vs oem and now it's an argument about racism, yep it's arboristsite where most want to talk about saw related stuff or boobs but a few who are not mods have to try to police the forum and can't let it go.

 

[cuinrearview]

Bill starts a thread asking about aftermarket vs oem and now it's an argument about racism, yep it's arboristsite where most want to talk about saw related stuff or boobs but a few who are not mods have to try to police the forum and can't let it go.

He'll have a place here down in the politics and religion forum. They love race baiters down there.

 

[TBS]

He'll have a place here down in the politics and religion forum. They love race baiters down there.

LOL, they're a very accepting group of individuals.

 

[Huskybill]

Race baiters, racism? Where did we take this turn? Oh boy.....

 

[TBS]

Race baiters, racism? Where did we take this turn? Oh boy.....

It doesn't take much to go that way apparently. Back to the topic, cylinders from huztl in my experience have always had some type of issue like casting flash in transfers, bad plating, and poor beveling. I've bought cylinders for 52cc clones that are miles better than what huztl makes for it's kit saws and built ones. Hyway and meteor can be near or as good as oem at times but has a fair bit of inconsistency. Imo stick to oem if you want it to last.

 

[Huskybill]

Bill starts a thread asking about aftermarket vs oem and now it's an argument about racism, yep it's arboristsite where most want to talk about saw related stuff or boobs but a few who are not mods have to try to police the forum and can't let it go.

It didn’t turn into an oil thread yet? Lol