Despite the air filter I like the 361. My wears a 22" bar and skip chain. It's a 3/4 wrap saw BTW. More than likely it stays on the floor in the back seat as insurance. (I'm running equipment more than sawing right now.)
2016 MS361 roll call, who's still got one?
- Thread starter wood4heat
- Start date
Help Support Arborist Forum:
Have any of you 361 owners compared your original to the Hutzel/Farmertec MS361 kit saw?
I recently assembled one and in the shakedown phase.
I'm mostly having trouble with the Choke/run/off control. Slips to full choke when you trigger it off fast idle.
Also, how many turns out on the low speed jet screw?
Thanks fellas!
I recently assembled one and in the shakedown phase.
I'm mostly having trouble with the Choke/run/off control. Slips to full choke when you trigger it off fast idle.
Also, how many turns out on the low speed jet screw?
Thanks fellas!
I've never had any trouble with the choke on my 361, don't know what would cause it to go to choke other than maybe putting something on backwards or something like that, maybe the little dogbone is catching the choke lever on the wrong side? Most low speed screws are at one turn depending on which carb you have. I put a Zama on mine and it worked better than the Walbro and it didn't have limiters.
I'm afraid the Farmertech might win in a comparison with mine since mine has a few miles on it..
Oh Really?
Farmer Johns Cousin
ArboristSite Lurker
I bought a Brand new MS 362 today. I mean a regular 362.... I realize it a strato saw but no M-tronic stuff. This one said it was made in Germany...My dealer had two more sitting there... not sure if any of this matters or what but I jumped.
As purchased - used:
Sporting a new bar and WWS sticker:
Custom bar modification to reach around for those hard to get limbs:
Lined up for a weigh-in with its cousins:
Ron
Sporting a new bar and WWS sticker:
Custom bar modification to reach around for those hard to get limbs:
Lined up for a weigh-in with its cousins:
Ron
earlthegoat2
ArboristSite Guru
Went to the pawn shop today to look at the chainsaws, they seemed to have a bunch this time but kinda pricey. A Stihl 362 for $600 seemed kinda high to me, an Echo 590 for $300, I thought they sold new for about $339. Anyway I didn't buy...I guess a 361 and 362 are a bit different?
Think 044/MS440 vs MS441.
I've never owned a 441 so I have no clue what they're like. The 362 did look a bit different than my 361 however.
They're completely different saws from the ground up.
Den69RS96
ArboristSite Operative
I still have mine. I bought on here about 5-6 years ago. I put a 20 inch Stihl es bar, new air filter, and a new side grill on the flywheel side because mine was all cracked. It's my favorite saw of the three I own.
I mainly use my 250. Most of what I'm cutting is under 10 inches and I do like it's power, size, and light weight. I like to use the 361 for anything between 10-20 inches and my 046 with a 25 inch Stihl es bar for anything larger. I know I could use the 361 for pretty much all of that, but I like to play with the others too.
I mainly use my 250. Most of what I'm cutting is under 10 inches and I do like it's power, size, and light weight. I like to use the 361 for anything between 10-20 inches and my 046 with a 25 inch Stihl es bar for anything larger. I know I could use the 361 for pretty much all of that, but I like to play with the others too.
Ryan'smilling
Addicted to ArboristSite
For a fun time, go to left coast supplies website. There you can buy a 16" GB bar for your 361. For like $9 or $10. Get a couple of chains while you're there. A 16" bar on that 361 will be more useful in little wood like that, so you'll get to use your favorite saw more.
crotchclimber
ArboristSite Operative
Here's mine. I have some aftermarket dogs on it and a 20" Oregon Prolite bar. I still need to do a muffler mod but that means making a deflector.
I still have 3 , my oldest pawn shop special was cutting firewood today
Here's an almost brand new one that I ported today.
Here's mine. I have some aftermarket dogs on it and a 20" Oregon Prolite bar. I still need to do a muffler mod but that means making a deflector.
Built in deflector.
Slit the left side of the muffler.
Ive posted this one once, but heres my ms 361. I bought it from the rental shop im a hired hand at for 10 bucks but it was rough, engine was perfect though. Put a bunch of parts in it big pto cover, big double dogs, tank guard and a 25" bar. Still need to track down a chain brake, mine is been repaired.
