just watched this vid and was wondering what yall thought was the reason the saw bounces so much during the cut. got a couple of ideas but not sure.
YouTube - Video Sears 3.7PS In the cut.MOV
YouTube - Video Sears 3.7PS In the cut.MOV
bouncing saw
- Thread starter jerrycmorrow
- Start date
Help Support Arborist Forum:
mark360T
ArboristSite Guru
I am gonna take a wild guess and maybe its due to using barracuda chain aka power sharp chain, that all i can think of.
redfire312
ArboristSite Lurker
badly filed rakers maybe? wore me out just watching some of it
Sport Faller
Gate Pimp
+1 i think one of my fillings rattled loose
broken or blunt teeth, or a broke raker, or the wrong angle on the raker, or maybe even wrong angles on the teeth.
Assuming nothing is broken. Rakers not rounded off or too low. Wrong cutter side plate angle or top plate cutting (not filing) angle, especially if the chain has been ground.
Out of interest is this what happens if you use a ripping chain to crosscut?
Out of interest is this what happens if you use a ripping chain to crosscut?
Last edited:
o8f150
Tree Freak
my shoulders are hurting from just watching it,,, i think my 370 echo would have whooped it
Would any of you know whether the saw is a poulan or a roper? That looks just like a sears saw I use to run that belonged to my uncle.
MCW
Somebody's talking crap here & it ain't the tree!
I think there are a few reasons this saw is bouncing madly in the cut. He's obviously got something going on here with raker height etc but the fact he's not running spikes on the saw is making it a whole lot worse. There is nothing to stabilise the saw in the cut. Even though his chain specs are out of whack I'd bet with spikes on the saw it would be hardly noticable.
This is EXACTLY what happens when trying to crosscut with ripping chain. I tried it once and only once. Punishing on yourself and your saw, and not to mention dangerous, particularly in hardwoods. I bought a heap of Carlton Ripping chain for a bargain from a Sten's sale a few years ago for about $100/100' (plus $100 freight to Australia
). Best bit is that it is a Semi Chisel profile with 10° cutter angle. I just reground it to 30° and dropped the rakers a tad and ah la Semi Chisel on the cheap
This is EXACTLY what happens when trying to crosscut with ripping chain. I tried it once and only once. Punishing on yourself and your saw, and not to mention dangerous, particularly in hardwoods. I bought a heap of Carlton Ripping chain for a bargain from a Sten's sale a few years ago for about $100/100' (plus $100 freight to Australia
). Best bit is that it is a Semi Chisel profile with 10° cutter angle. I just reground it to 30° and dropped the rakers a tad and ah la Semi Chisel on the cheap 
homelitejim
Full of Scrap
Roper
Some are hinting that it is the saw itself. When the chain speed is slow enough, even a new chain will bounce like that. . . .
MCW
Somebody's talking crap here & it ain't the tree!
He needs Popeye style forearms like yours to hold it stable
You're right though but I think something else is at play here and I'm betting if he had felling spikes on the saw it wouldn't look anywhere near as bad.
homelitejim
Full of Scrap
Here is a video of me with a Montgomery Wards 3.7, no dawgs on this saw and I'm sure the chain is something that I got for free somewhere because I pulled it out of a box. It is not bouncing around but I am having a hard time getting it to pull itself in the wood, here a set of dawgs would have helped so I am going to say the original saw has a chain problem.
[video=youtube;hcYPsh9CbF4]http://www.youtube.com/watch?v=hcYPsh9CbF4[/video]
[video=youtube;hcYPsh9CbF4]http://www.youtube.com/watch?v=hcYPsh9CbF4[/video]
SDiver40
ArboristSite Member
I'm leaning towards the rakers filed too short or broken
MCW
Somebody's talking crap here & it ain't the tree!
My last name is Ward and I believe my Grandad, Montgomery, may have owned that company.
OK, maybe not...
