If you could only have 2, what would they be?

[K7NUT]

Judged by your user name, it looks like you may be a bit dyslextic? :msp_confused:

You may think so saw, but it makes perfect sense to the FCC's!?
That's the Federal Communication Commission

 

[KodiakKen]

where are the die hard Stihl guys

I didn't see anyone suggesting a 200t or the (I hate to say) 201t and 660. my go to saw is the (dammit here I go again) my 201 modded. if that can't do it or in oak I grab the 360..if that won't do it..660..if that won't do it..I don't need it. I have always run my 360 as my go to saw. not too much to lose control but enough grunt to get it done with a 20" bar.

 

[greendohn]

My 372xp and CS 400

That's real close to what I'm running,,,cs400 and 2171, and old beat up truck.

 

[exSW]

Dolmar 420 and a 70cc Pro saw.Where I'm at right now.

 

[rdtreewalker]

562 & 395, both ported

 

[blsnelling]

346XP and 390XP.

 

[bcaarms]

346 xp. 2253. 2260. 2181

Yeah yeah I know that's not two. If I was going to fix cars I wouldn't just buy 2 wrenches. Each wrench has its use. Picking two is stupid. There are tools made to make the job safer and by keeping you out of danger zones. So my advice is don't try to figure out the best two saw combination. Any selection of 2 will have you not as we'll equipped as people with larger selection.

Just my advice. You can go that route if you choose.

 

[ttyR2]

026 Pro for little stuff, 046 with various bars for everything else. Loooove that 046...it's glorious. Chicks dig it too.

 

[rocketnorton]

pioneer ra & p40. 2 of my favorites of 10...

 

[rms61moparman]

For the best value I would keep my 401 or 420 and a 6400.
I can cut (comfortably) 99% of everything I cut with those two.

I also have a 346/372 combo that is as good as they get! (thanks Andyshine77)

Or, if I wanted to creamsickle, I could cut anything I need with my 032 and 056 Super.


An S25 and 4000 (or 5200) Poulan would also suffice.
A 3000 Poulan and a 7900 Dolmar would work out well also.
Or a 5000 Partner and 10mm 044.

Poulan Pro 295 and a Poulan 5400?


The possibilities are really endless!!!!

How about a Poulan 2700 and a 3750 Bad Boy???


Mike

 

[CapitaineHaddoc]

560/562XP and 390XP/MS660

And if i could only have one, it would be a Dolmar 7900.

 

[sachsmo]

7900 and 166

Dats all I really need.

 

[Species 8472]

MS 261C and be one of the first to try a MS661C ported.:redface:

 

[wndwlkr]

Dolmar 32 & 7900

 

[nmurph]

346 and 7900.

 

[Vermonster]

The best 50-ish cc and 70-ish cc saw money could buy. You tell me which ones they might be.

 

[Homelite410]

Super2 and Sxl

 

[GPX433Todd]

290 & 461

 

[Showme]

I think for me it might be my MS261 & MS440/460, both Snellerized.

 

[zogger]

Only two saws makes it rough, but..lot of big mature trees here, big ones, so I would have to say around a 50, then an 80-90ish.

One saw, a 60ish
three saws, 40,60, 80-90