Snellerized Saws Re-Visits the MS241C

[KG441c]

Should I sell my 346 now before this cataclysm occurs? I dont want to be left behind. I really do like that little 241 even in stock form with the right chain it is definitely my favorite.

Brad has it figured on this 241 . Send it to him

 

[lone wolf]

Brad has it figured on this 241 . Send it to him

Got the time differences from stock to modified does it lose low end power and shine in the high end or make good power all the way up?

 

[blsnelling]

Should I sell my 346 now before this cataclysm occurs? I dont want to be left behind. I really do like that little 241 even in stock form with the right chain it is definitely my favorite.

My 346 is going nowhere Put a 20" .325 B&C on the 241 and watch the 346 shine!

 

[blsnelling]

Got the time differences from stock to modified does it lose low end power and shine in the high end or make good power all the way up?

Not in the least. It gains tremendously across the entire RPM range plus gains a lot on the topend. Watch me lug it down in the video.

 

[lone wolf]

My 346 is going nowhere Put a 20" .325 B&C on the 241 and watch the 346 shine!

I use the 241 for just limbs when taking a tree down and I like it better then my 346 something must be wrong with that saw I ain't happy at all with it.

 

[lone wolf]

Not in the least. It gains tremendously across the entire RPM range plus gains a lot on the topend. Watch me lug it down in the video.

What percent did you gain in speed ?

 

[blsnelling]

I only ran it for about 10 seconds after pulling it out of the box new to make sure it ran right.

 

[stihlaficionado]

Definitely keep the 346. Then get the 241 & 261 Snellerized…next up is the 150 top handle

 

[lone wolf]

Well Brad I seem to have a problem tuning the 346 do those jets move much with the limiters off and do you know the stock adjustments?

 

[blsnelling]

They shouldn't. No I don't. I'd start with both 1 1/4 out.

 

[porsche965]

Well Brad I seem to have a problem tuning the 346 do those jets move much with the limiters off and do you know the stock adjustments?

Get a 550xp! Snellerized of course.

 

[Stihl 041S]

take a bit to set this job up. 6m bar in a 1.5m lathe. have to thread both ends with a 8mm pitch ACME thread.

Pump shaft?

 

[VinceGU05]

Pump shaft?

Tiebar for a Diecasting machine.

 

[blsnelling]

Here's another 241 I finished up today. These saws come with a 6-pin spur. This one's wearing a 7-pin rim. It has plenty of power for the larger sprocket.

 

[chris zautner]

I'm starting to get a real itch for one of these 241c's

 

[blsnelling]

These new mods make a world of difference. It takes the saw to a whole different level. I'm very pleased with them now, so much so that I'm keeping the one I bought to experiment on. I used it a couple weeks ago to help my next door neighbor with a tree.

 

[caffeine1fg]

In the name of science I'd loan you mine to experiment on. lol.

Good work, impressive!

 

[KG441c]

Mine wont be goin anywhere after this type port work was put in it

 

[stihlaficionado]

Here's another 241 I finished up today. These saws come with a 6-pin spur. This one's wearing a 7-pin rim. It has plenty of power for the larger sprocket.

 

[Four Paws]

What do these 241 Stihl saws sell for? How much is the rim/clutch drum upgrade?