Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Looking for a handlebar,Bearing spacer,Worm gear and spring for an 044
 
I would like to trade. I have 056 clutch cover,early style as shown in photo with the shelf (step) bar nut hole. Working chainbrake. Very good condition.
Would like to trade for 056 clutch cover with chainbrake without the step up hole.
yosh062.jpg
 
Looking for a handlebar,Bearing spacer,Worm gear and spring for an 044

I have a heated handle bar, don't know what the bearing spacer is, worm gear and spring for 044.

I have everything for 044 other than P&C here that I'm giving up plus a extra crankcase off 440 that I was going to use. all up for a grab/trade.
 
I have a bunch of NOS Homelite parts from the 70's and 80s's, I would need the part number and description of what you want. I would like to trade for running or non running pro Husqvarnas or Jonsereds. My father was a dealer in 1973 to 1986 so I have quite a bit.

Do you have a good P&C and rings for a C-51?
Trever
 
The vintage Husqvarna bar I posted above is mailing out this afternoon.

Other stuff I can live without:

A. I have a couple large mount Stihl bars that I could live without - 24" vintage hardnose and low-hours (more like minutes) 25" GB ProTop with a 3/8" tip. Both bars are .063.

The Stihl bar is shown here:
Side_075_Stihl_02.jpg


The GB bar is shown here:
Big_Stihls.jpg


B. Oregon clutch drum and floating rim system for Stihl 075/076. New in box.


I might also consider letting the following saws go, for the right trade:

1. Like-new Dolmar 5100s, 18" bar and 3/8" chain. It was a Cutting Edge demo saw that I bought from RBinVA in September. I haven't even fueled it up since I bought it from him...makes me think I probably didn't need it.

2. Stihl 075. Strong saw in good condition. .404 spur sprocket. Starts on 1 pull if you can flip the choke off quick enough, otherwise it's a 2-pull saw. Only "defect" was that it kept rattling the clutch nut off, and started to wear a hole through the clutch cover. Replaced the clutch nut and didn't have a problem in the 1/4 tank I ran after replacing the nut; the nut looked like crap but the crank threads looked ok. PHO.

Close_up.jpg


May7-2007226.jpg


3. Ford Eagle (Eagle II?) chainsaw by O&R. I've got a 16" hardnose bar for it. It is very clean and could be tidied up quite easily. Needs a carb kit/fuel line/filter, and a new pull rope. Piston looks good. Ran fine until it sat for a few years.

Ford_1.jpg


Ford_2.jpg


Ford_Eagle_II.jpg

(before I cleaned it)



I'm not 100% about wanting to get rid of these saws, but if the right deal comes along, I'm game for it. I'm looking for a good condition 371/372, 044/440, or Dolmar/Makita 64-7900.
 
I'm in need of an airfilter cover for a Stihl MS260, handlebar(s) for 024/026, and clutch cover for Dolmar 100 or 102.

I have new B&C combos 16" and 20" that fit McCulloch Pro Mac 605, 610, Timberbear, etc. I also have a PM610 that I bought new with its original hardcase and a new carb for the PM and Timberbears.
 
I have a good 3120 jug with a so-so piston that I don't need. I don't know if you'd want to use the piston or not, it has a bit of scuffing on the corner of one skirt. The cyl looks good though. I can try to send pics to anyone that's interested, if they can be patient. I've got a lot going on right now.
 
I have a New never used 36" stihl 3/8 .063 rollomatic E 113DL with a new never used stihl full skip square chisel(RSLFK) chain. 113 DL
Used 36"rollomaticE 3/8 .050 114DL with one woodsman pro semi chisel and two stihl RSC chains all chains good.All 3 chains 114DL
What ya got for trade.
I wouldn't mind a dealin for a new 32" or 36" cannon superbar
gregz
bc001.jpg
 
I have a JRed 2036 turbo I picked up today. It seems to run good, I plan on working it out tomorrow. It has a brand new Husky brand bar and safety chain. I'm open to lots of trades, maybe a project saw, 026 parts, stihl rsc chains, vac/ pressure tester, flywheel puller, let me know. The only issue with the saw I've noticed so far is that the handlebar has been repaired- it appears to be pretty solid. If I find any more issues I'll point them out. At this point I have $50 in it approx.
 
460 clutch needed

I need some good clutch shoes, and a factory inner "big" felling dawg. I have several 031 parts including an excellent P&C (165psi before pulled) i am willing to trade. Also have some various cheap poulan saws for parts(wildthingys and such).
 
I am looking for a few small parts. I could use 1 or a few screw and "bell washer" that goes through the chain brake handle into the starter cover for an 026 style saw. I also could use the inner bar plate and screw that covers the chain adjuster.

I have fuel lines, carb kits, Stihl torx screws all of various nature. I also have a new ignition module for the 1130 series saw. The part # is 1130 400 1300
 
I have a 32 inch stihl ES bar 404 063, comes with 2 chains.. I would like to trade for a comparable bar in 3/8 050.. brand does not matter, just has to fit an 066.. I would prefer replaceable tips, but thats not a deal breaker..
 
i would possibly trade my 084 for 460 in very good shape or 372xpw.


i also am in need of 044 piston 10mm wrist pin and muffler. and air filter and cover ohhhhhh and chain case cover
 
Back
Top