Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
QUOTE=hseII;228633]Need MS460 and 044/MS440 parts;
good plastic
MS460 clutch
MS460 oiler
MS460 carburetor
MS460 Clutch Cover
MS460 Tank Assembly
044 tank assembly

Trade Fodder;
1) Homelite C5
5e7ave2a.jpg

e9ega2aj.jpg

rusy7e2e.jpg


2) Stihl 028
4a3usygu.jpg

sejyberu.jpg

7a7ugeha.jpg
egenupen.jpg


3) 044/MS440 Cases, Slugs, and Jugs-
3 complete non running and a bunch more loose
y2edyzet.jpg

e6ytypy4.jpg


4) MS290 parts saw
5) MS310 that is running; both are in the pic above

6) 064 NOS tank/handle assembly still in the plastic

And if Course Trade Paper
[/QUOTE]

I have the oiler you need.
 
I'll need an address.... My mind reading abilities are low when I have a crappy day. Might as well just send it to me in a pm... Tomorrow's not looking good either..;)
 
My wife already owns them. Sorry.


I have a clutch nut from a john deere 50v right here. I believe it's the same. "Looks like" a reverse thread 5/16 nut. Yours for shipping.

For anyone that may be in the need of hardware like a LH nut on a echo or echo /Deere i found out the hard way Deere crossed all the Echo numbers for standard hardware to Deere numbers. A LH flywheel nut for a 50VL was less than $1 at Deere and $10 (freight) at a fastener place. You can guess witch one I had in my hand when I found this out. My local Deere showed like 50 nuts on hand too.
 
For anyone that may be in the need of hardware like a LH nut on a echo or echo /Deere i found out the hard way Deere crossed all the Echo numbers for standard hardware to Deere numbers. A LH flywheel nut for a 50VL was less than $1 at Deere and $10 (freight) at a fastener place. You can guess witch one I had in my hand when I found this out. My local Deere showed like 50 nuts on hand too.
My local deere dealer was just shut down. One day JD showed up with tractor trailers and just hauled it all away.
 
Well times are changing for me and I must weed out the project/parts pile O' junk.

I have a few projects that I would like to complete, needs;
Stihl 064: needs a bunch of stuff, carb and associated pieces for HD filter setup, piston, AV mounts, clutch cover and bunch small bits.
Stihl 015L: P/C (have bits for second 015 that could be barter material, have to look)
Husqvarna 45: recoil cover and inner liner

Have mucho stuff to barter/unload:
Husqvarna 40 (x2): parts/projects
McCulloch M47: good project, mostly there, good P/C, missing muffler and mesh cover for recoil. Never tried to run w/o muff
Skilsaw 1616 delux type 3: roadside pick, got running after carb clean
Homelite little red XL: ??
Echo CS-601 SVL: estate sale pick, complete with manual. Cleaned carb, replaced line, it ran but not idle IIRC, far as I went.
Sears D-44: another estate pick, mostly there, P/C looks good. Recoil needs work and ?
Pioneer P20: don't remember, never messed with...
Pioneer 1200A: looks complete, never touched it
Pioneer 3270: wrap handle, looks fairly complete as I recall... Spoken for by Jacob J
Pioneer P40 (x3): projects, two mostly there, one clearly a doner, one stuck cyl, other ? Far as I got...
The pioneers I picked up as a pile and never got around to doing anything with, time to give up to someone with more time than me.
Stihl 044 parts gone to shawn022
Jonsered 630: basically just a crankcase/rear handle tank assembly with upper handle and jug. Looks like heated handle option. Slug n jug questionable

Have a pile of other saws, mostly late model stuff, Homies, Poulan, JD, ???. Stuff that just followed me home somehow, will update list when I look over the pile again. May have some other Stihl stuff too after I assess whether I "need" it or not. Might have an 031 that could go and some 028 & 048 bits as well, stand by... PM me if you desire more info or pix of a particular project piece.

Edit to add following available;
Stihl 031AV: missing chain break bits, rest appears correct. Never messed with
Husqvarna 266: bare crankcase halves and rear handle tank
Craftsman 42cc: no idea, probably bad p/c. Good plastics
JD CS40: parts saw hold for Mo. Jim
Mac 110: parts saw, missing top handle hold for PA Dan
McCulloch : top handle, looks like older 110. Mag cases
Poulans: x4, 1950 wood shark, 2x 46cc, 42cc. Parts/doners
 
Anyone need some husky concrete stuff? Didn't know if any one was milling with a 372 and wanted a concrete filter set up like some do on the 075/076's. Tank will stay here but the front handle is available. I might have a faded 372 tank that can go as long as this tank is good.
 

Attachments

  • image.jpg
    image.jpg
    146.5 KB
looking for a few dried up corn cobs,,,, all I have now for trade is some useless green wrinkled paper,,,,, i have a serious case of hemorrhoids,, i heard dried up corn cobs are a sure cure for them
 

Latest posts

Back
Top