Guys With Band Saw Mills

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I guess thickness and board ft per hour is going to depend on what shape you want to mill and the thickness of that shape.
So if I wanted to mill a pine tree into boards for siding, what thickness should I most often cut to?
The milled lumber will be used as siding for some outdoor structures such as wood shed and storage shed.
My miller says about 1.5 inches (or 6/4) thick.
He says 6" board too but I'd like to board and batten the sheds as wide as possible.
Any suggestions from some who've done this and why?
 
Now that more is added get the guy mentioned and watch. Have lots of long saw horses ready to put non edged pieces on. Have disposal of scrap thought out.

Board and batten is most always 1", from my observation. I do not choose that type of siding.

If you want wide, slice off two sides 180 degrees apart as opposed to aiming for a square can't. When down to 6" or so cut up the other way.

A band sawmill is kind of inefficient in dealing with stuff that has bark on two sides, even more so if you want to maximize board size by doing the edging one piece at a time. Perhaps from the production quoted to achieve the 4 hour estimate the intent is for you to edge with a table saw or something of that nature. An edger in addition to the band mill will make things less stressful and more productive per unit time.

I think the quarter scale is for hardwood and 4/4 is an inch and an extra eighth, 8/4 is two inches and an extra eighth. That is pretty much what one gets when going off a magnetic scale that comes with sawmills or can be ordered from their manufacturers. 4/4 is definitely thicker than if I go for 1 1/16.
 
Now that more is added get the guy mentioned and watch. Have lots of long saw horses ready to put non edged pieces on. Have disposal of scrap thought out.

Board and batten is most always 1", from my observation. I do not choose that type of siding.

If you want wide, slice off two sides 180 degrees apart as opposed to aiming for a square can't. When down to 6" or so cut up the other way.

A band sawmill is kind of inefficient in dealing with stuff that has bark on two sides, even more so if you want to maximize board size by doing the edging one piece at a time. Perhaps from the production quoted to achieve the 4 hour estimate the intent is for you to edge with a table saw or something of that nature. An edger in addition to the band mill will make things less stressful and more productive per unit time.

I think the quarter scale is for hardwood and 4/4 is an inch and an extra eighth, 8/4 is two inches and an extra eighth. That is pretty much what one gets when going off a magnetic scale that comes with sawmills or can be ordered from their manufacturers. 4/4 is definitely thicker than if I go for 1 1/16.
All good info. Thanks.
I guess I have this analytical mind, but most guys around here want to build you board and batten siding on just about everything.
It's kind of a copy-what-the-last-guy-did mentality.
Although it looks ok to me on small outbuildings, I'm not convinced I like the aesthetics of it on large surfaced structures like a house or garage.
I prefer the look of horizontal siding for these.
But I have this big White Pine to be felled and I need to plan to use it in some way so I thought why not use it for siding for a shed and a long lean-to woodshed.
We are also building a two-car, lean-to styled carport so I may be able to close in the sides partially and maybe use it for making some rolling barn doors for it too. All of which I've never built before...lol.
 
All good info. Thanks.
I guess I have this analytical mind, but most guys around here want to build you board and batten siding on just about everything.
It's kind of a copy-what-the-last-guy-did mentality.
Although it looks ok to me on small outbuildings, I'm not convinced I like the aesthetics of it on large surfaced structures like a house or garage.
I prefer the look of horizontal siding for these.
But I have this big White Pine to be felled and I need to plan to use it in some way so I thought why not use it for siding for a shed and a long lean-to woodshed.
We are also building a two-car, lean-to styled carport so I may be able to close in the sides partially and maybe use it for making some rolling barn doors for it too. All of which I've never built before...lol.

I’m Not familiar with white pine, but yellow pine is great for roof lath, interior wall coverings, flooring, etc.

I would think if you use it for exterior siding you will need to coat or treat it.

Please take pictures of the process.

My father on the LT-40 hydro sawing yellow pine that I felled.
f46503899896a9689f31364a41f225ac.jpg
 
I guess thickness and board ft per hour is going to depend on what shape you want to mill and the thickness of that shape.
So if I wanted to mill a pine tree into boards for siding, what thickness should I most often cut to?
The milled lumber will be used as siding for some outdoor structures such as wood shed and storage shed.
My miller says about 1.5 inches (or 6/4) thick.
He says 6" board too but I'd like to board and batten the sheds as wide as possible.
Any suggestions from some who've done this and why?

For siding we do 1/2, 3/4" or 1" 6 or 8" width. 1.5" is way too thick.
 
I really like the look of board & baton siding, I milled this out at 5/4 to get some thermal mass,

standard.jpg



One thing about it, it goes up fast and if installed right, it does a good job...

standard.jpg


Like I said, I like the look,

standard.jpg


BTW, this is white pine siding...

SR
 
I’m Not familiar with white pine, but yellow pine is great for roof lath, interior wall coverings, flooring, etc.

I would think if you use it for exterior siding you will need to coat or treat it.

Please take pictures of the process.

My father on the LT-40 hydro sawing yellow pine that I felled.
f46503899896a9689f31364a41f225ac.jpg
Yes you need to treat White Pine to prolong is lifespan outdoors, but like all pines, it has some natural protection from it's pitch. I will stain any projects I build with it.
I've got some Yellow Pine 2" x 10' boards from an an old waterbed and they are heavy a hell.
White Pine is a lot less dense, more like Spruce or Fir.
Great pic of milling. Why was the live edge left on one side there? Just wondering.
 
Yes you need to treat White Pine to prolong is lifespan outdoors, but like all pines, it has some natural protection from it's pitch. I will stain any projects I build with it.
I've got some Yellow Pine 2" x 10' boards from an an old waterbed and they are heavy a hell.
White Pine is a lot less dense, more like Spruce or Fir.
Great pic of milling. Why was the live edge left on one side there? Just wondering.

Sometimes we will saw like that & then stand them all vertical & take all that off at 1 time.
 
Nice building!!--that siding would make it easy to heat!--Also nuttin' wrong with board and batten siding!! I always liked it.--I guess everyone has different ideas about it! thanks; sonny580
 
Back
Top