McCulloch 28" bar for sale, fits poulan, echo and many others

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Freakingstang

Doctor Freakinstein
Joined
Dec 23, 2005
Messages
5,648
Reaction score
1,135
Location
NE Ohio
This is a McCulloch branded Winsor Sanvick bar. it is the smaller mount Muc-a-luck mount. It crosses to an oregon D176. Should fit a variety of Mac's, echo's, and many others

This is a 3/8 050 28" bar. Bar is straight and looks good. It could probably use a touch up grind and squeeze to true it up, but it doesn't look too bad to run it the way it is.

Would like $25 bucks plus $10 shipping.

Should fit the follwing saws according to the oregon site:

ALLIS CHALMERS-95, 195, 295
DAYTON-2Z462A, 2Z463, 2Z561, 2Z971, 4Z251, 4Z252, 4Z397, 6Z826, 7Z627
ECHO-CS-60, CS-451, CS-452, CS-500, CS-501, CS-510, CS-550, CS-601, CS-602, CS-60S, CST-610, CS-650, CS-660, CS-701, CS-702, CS-706, CS-750, CS-6700, CS-8000
FAIRMONT-H6200B
GREEN MACHINE-7600, 7700
JOHN DEERE-50V, 51SV, 55SV, 60V, 65, 65SV, 66SV, 70V, 80EV, 800V
LOMBARD-AP-42, SUPER LIGHTNING, LIGHTNING III, COMANGO, CS-3500, CS-3501, CS-3502, CS-3503
MCCULLOCH-1-10, 2-10, 3-10, 4-10, 5-10, 6-10, 10-10, 55, 57, 60, 80, 555, 560, 570, 610, 650, 655, 700, 800, 805, 850, 1000, 3720, CP55, CP70, DOUBLE EAGLE 50, 80, EAGER BEAVER 3.7, PM605, PRO MAC 5700, 8200, SILVER EAGLE 3420, SP60, SP70, SP80, SP81, TIMBER BEAR, TITAN 50, TITAN 57, TITAN 70
MONTGOMERY WARD-TMY13083, TMY24084, TMY24086, TMY24088
POULAN/POULAN PRO-203, 245, 306, 360, 375, 361, 395, 400, 450, 3400, 3700, 3800, 3900, 4000, 4200, 4400, 4900, 5200, 5400, 5500, 6700
REDMAX-G561AVS, G621AVS
SEARS-35145, 35212, 35483, 35608, 35609, 35690, 35721, 35727, 35728, 35826, 35829, 35851, 35881, 35885 ELECTRICS (1983 models forward), 35887, 35889
SKIL-1641
TANAKA-ECS-505, ECS-506, ECS-650, ECS-655
WESTERN AUTO-430, 3400, B013, WIZARD AV-18


attachment.php


attachment.php
 
Any chance of getting a close up of the tip. About the last 6 inches of it? I have a CSM and I drill the bar for the clamps. I'm wondering if there is a place to drill it or if there already is a hole there to mount it to my mill. Thanks. If you think it is drillable (room near the tip) or already has a hole, then that'll do as well. Thanks.
 
Back
Top