Power Products Thread....any and all info welcome.
- Thread starter wigglesworth
- Start date
Help Support Arborist Forum:
Warped5
WingNut
AH-47 engine with Tillotson MD-60A carb ...
Carb QOD: The carb has a 'main channel' running from front to back and I'd like to get it cleaned out. No question in my mind that it needs it. There are plugs at each end; what material can I replace these plugs with if I remove them? Thanks!
Carb QOD: The carb has a 'main channel' running from front to back and I'd like to get it cleaned out. No question in my mind that it needs it. There are plugs at each end; what material can I replace these plugs with if I remove them? Thanks!
Shooting from the hip, lead buck/bird shot comes to mind.
Back in the 'olden days' automotive carb. kits sometimes came with small lead balls to reseal a passage or two.
Gas was .19.9/gal. and I drove my '52 Olds all week on two bucks.:msp_ohmy:
Enuff room to tap for a small and short socket set screw?
Warped5
WingNut
Carl, you got me thinking .... I need to plug about 1/16" at one end and about 1/8" at the other. I think lead shot and a set screw would be just the tickets! Thanks!
Warped5
WingNut
Update: I found a complete carb kit and some bits at Discount Marine. Will stop by the local hardware store this afternoon to check out these set screws ....
little possum
Crash and Burn
paccity
Addicted to ArboristSite
rootin around and realized i had twins.
paccity
Addicted to ArboristSite
and a few more that need cleaned up.
Warped5
WingNut
Looking for crank seals for my AH-47 David Bradley (Strunk). All the info I've found this morning is inconclusive.
Any help would be appreciated!
Any help would be appreciated!
What size is that Wards/Remington?
paccity
Addicted to ArboristSite
paccity
Addicted to ArboristSite
wards, i like the plug cover.
Yup. Wards/Remy PL-4. Too bad I have two or three now.
I have been looking for a serviceable PL-5 or SL-11 piston.
I don't know what the deal was but, all the Wards marketed saws have the squared off recoil housing. Just to make 'em different, I suppose.
Last edited:
Warped5
WingNut
I should clarify ... actually looking for the part number for the crank seals.
logging22
Cuttin to live, livin to cut
I have been looking for this info as well. For some time now. No closer than i was when i started looking. Probably just have to take one apart and get the mike out and measure it.
logging22
Cuttin to live, livin to cut
FOUND THEM!!! Part number is 510105 or 510319. Get this. They are in stock. 7.99 ea. How kool is that.
paccity
Addicted to ArboristSite
diggin again and now triplets.
Warped5
WingNut
I went chasing this down today ...
While I was reasonably sure of the number(s), there was just enough missing information on Sears site to cast some doubt. Did some digging, called some numbers and talked to some folks.
The 510319 supercedes 510105 and is valid.
Seals ordered.
.. just hope I can get enough fresh fish to keep them fed. :jester:
I posted this a while back to see if anyone could identify it, and was told it's an AH47 powerplant.....but it's a left handed saw. I need a new top end for it, I assume a normal AH47 top end will work if I rotate the cylinder 180 degrees. Any thoughts? Any idea who made it?
Since the Power Products AH-47 engine is so common, can I take one from a David-Bradley and bolt it to my Indian 351D chassis?
The Indian pumps only 70 psi. But, has spark.
The Indian pumps only 70 psi. But, has spark.
