Search results

I would but it's a little rough just above the exhaust port. The Meteor pistons seem to be good but they don't make cly for 028S

Anybody have a good used OEM cylinder for 028 super, could be with or without piston

Any recommendations on a good after market cylinder for 028 super. Seems some brands are not highly thought of. It seems Meteor only makes piston. Any issues with putting Meteor piston in other brand cyl?

Anybody have a source for 26RMC 67 (semi chisel, non safety) Chain? Thanks

Thanks but in my case you can see the gas coming thru the muffler when you are just cranking it over.

The one thing I didn't replace is the little plug on the metering side of carb. Could this have anything to do with it?

I took the carb apart again, checked location of gaskets, diaphragms, etc. This is a new carb kit. Checked vent hose. Still same problem. It's strange cause gas will start coming out through muffler while I'm cranking it over but it won"t usually start unless I take plug out and prime it. Then...

I get gas practically running out of the muffler on my 028. If I can get it to run, it smokes like hell. Cleaned carb with new kit but no difference. Any ideas? Thanks

Thanks for the comments. After thinking about it, it make sense that it is a carb/gas problem and only a coincidence that it happened when I switched to synthetic. I'll take the carb off and clean, etc.

What I don't understand is that it was running great, ran out of gas, put in gas w/synthetic, started it and it immediately started to smoke like mad. It seems the smoke is coming from the gas pouring out of the muffler. It seems like there is too much gas going into the cylinder. The carb kit...

Was just using my saw (028) with reg Stihl 2 stroke oil. I ran out of gas and put in gas with Woodland Pro synthetic. The smoke was unbelievable, ran like crap. Got it going again and gas was pouring out of muffler. Trying to retune carb but seems something else is going on. Any suggestions?

I do carpentry work for a living and have had the Panasonic EY6432 15.6 volt for about 6-8 years. A great tool, never a problem. I really doubt if anyone could tell the difference between 15 volts and 18. The drill has great balance and feel, much better than Dewalt, etc. The batteries are...

This is a pretty good list http://pure-gas.org/index.jsp?stateprov

I have an 028 Super. I could take a picture of the assembled brake system if it would help. I also think there are a couple of different brakes on these.

I have the large HF ultrasonic cleaner. When I use the heat mode, it doesn't seem to heat the water up at all. How much should it heat up?

Just got a HF flier yesterday. The $80 ultrasonic cleaner is on sale for $60.

I might end up going with the HF $80 one (90 w/ship).. Found the same one on Ebay for $84 incl shipping. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220561787041&ssPageName=STRK:MEWAX:IT857-491-145 The stainless ones are probably more durable but for my use, the cheaper ones will...

Is it a good size tank for saw, and other small eng carbs? Thanks for your help.

Has anybody had any experience with this cleaner? http://cgi.ebay.com/New-2-5L-Digital-Heated-Ultrasonic-Jewelry-Cleaner-250W_W0QQitemZ230441389096QQcmdZViewItemQQptZLH_DefaultDomain_0? hash=item35a7608c28 I've read about the HF cleaners but wondered if anybody had one of these. It has a...

Maybe it's their legal dept advising them not to sell the non anti kickback chain. Still it doesn't make any sense why some distributors sell it and some don't.