Husky 372 or 575xp?

[SawTroll]

hey troll, its a long story opcorn: opcorn: opcorn:


id tell ya all about it but it would end up on AS!!!

It wouldn't, if you told me not to.........

 

[dancan]

Is there an expected date for the end of the 372 ?

 

[gafirefighter]

I was told by my dealer yesterday that they are now out of production. Once the ones already made are sold there are no more. Not sure if this is correct though. You know dealers.

Adam

 

[2000ssm6]

lol, no bearing problems at all. they use a common bearing used on a tonne of husky saws already. different part number due to a small taper on the inner race to allow for the shape of the crank. the only 575 problems are bad tuning problems (human error), thats why the AT is being introduced...

Since you have both, which is the "better" saw? 575 or 372?

 

[stevethekiwi]

Since you have both, which is the "better" saw? 575 or 372?

hahahaha... i was waiting for that


A job thats mostly Med - Big wood - 346 + 575 + 395

A job thats mostly Small to Med wood 346 + 372 + 395


you dont notice the extra weight of the 575 in big wood as the saw is supported by the log anyway. and you save a tonne of fuel at the end of the week. its also less dependant on optimum rpm to get the job done

372 is more manoeverable, and checks all the boxes.

575 checks most of the boxes, some of them better that the 372. it just doesnt quite have the all round capability.

 

[2000ssm6]

hahahaha... i was waiting for that


A job thats mostly Med - Big wood - 346 + 575 + 395

A job thats mostly Small to Med wood 346 + 372 + 395


you dont notice the extra weight of the 575 in big wood as the saw is supported by the log anyway. and you save a tonne of fuel at the end of the week. its also less dependant on optimum rpm to get the job done

372 is more manoeverable, and checks all the boxes.

575 checks most of the boxes, some of them better that the 372. it just doesnt quite have the all round capability.

I figured it was best to hear it from a husky man who has both, thanks for the info, may help the op or other people out.

 

[Woodie]

Is there an expected date for the end of the 372 ?

There sure is.

Dec 2005, May 2006, June 2006, mid-June 2006, no...make that late May 2006, November 2006, May 2007...

 

[testlight]

It hasn't stood the test of time yet, but I have a 575xpw (w is from wrap handle). I like it a lot, lots of power, lots of torque. The saw does feel cold blooded at first, but it always starts and runs like it should.
I hope it holds up.

 

[beowulf67]

Just my observations......

Don't know if you pulled the trigger yet, but here are some of personal observations. I own and run both a Jred 2171 and a Husky 575XPG (old edition). Both of them perform both superbly and reliably. After spending some quality time with both, it is my opinion that the 575xpNE (or whatever it is called) will be an improvement over the 372XP.

I can hear those arrowheads whistling through the air So hold on.

I know that the 575xp has received alot of bad press here but there are ample owners/members who do like them. Let me reiterate that the 372xp/2171 are fine saws and their reputations are etched in stone. Period. A chainsaws' fit to an individual operator is very subjective and I like to run a saw with a beefy chassis. Here's why I feel the 575 WILL be an improvement
.
1. I think it was Andysunshine77 who mentioned build quality of the 575 and i could not agree more. The 575 is put together real nice with excellent fit and finish. The proof is in the details and I actually see many design elements of the 385/390 filtered down into the 575. This is obviously where the weight issues come into play. The following are parts which I noticed on the 575 which are shared with the 385 family saws: air filter, clutch cover, and increased diameter handle. With regards to the air filter, I am referring to low-top models. I am assuming that the HD filter setup would be the same filter also. If one wanted to install a full wrap handle setup on the 575 you have a similar/same(?) bolt pattern shared with the 385. On my 2171, the bolt pattern is staggered. Never took the time to investigate the ipl's, but maybe the 575 has a larger clutch?

The decomp button is very well placed and has nice little rubber grommet to keep dirt out. I also like the plastic grip on the rear handle. As I said, its all in the details.

IMO, the ON/OFF/Choke setup is a huge improvement over the 372/2171. I am not alone when I say that I had my original 2171 switch fail and needed replacement. Surprised me when I found that the new replacement was stamped "Made in Germany." I have to admit that the new setup looked flimsy in pictures. I was first exposed to this setup on my 2153 and was pleasantly surprised. Very user-friendly and Husky molded the plastic around the controls just right (good protection).

2. Performance and handling. With regards to handling, I give the 372 the edge. I am sure sure that other owners will agree, very maneuverable for a 70cc saw. Stock, broken-in, and tuned properly, the 372 just flat out flies with that nice, crisp throttle response. Modding the 372 puts it into another league. The 575, as you would expect, a bulkier saw to maneuver. Tough to describe in words but this strato engine kind of detracts me a little from the engine, if you will. Almost like "throttle by wire." Not necessarily a bad thing, just different from what one is normally used to. That said, the 575 has plenty of power, particularly in the low end. Strong performance. I have actually had 32" bars on both saws and if I had to pick a powerhead to to drive those extra drive links, its the 575.

Starting procedure on either saw has never been an issue.

Fuel economy? 575 hands down. I am still amazed at the amount of work this saw can accomplish on 1 tankful of mix.

Also, for those that care about heated handles, the 575xpg gets those handles nice and toasty quicker than my 2171WH. How much quicker? Enough to notice.

Back to my original statement that the 575 "will" be an improvement over the 372. The 372, to me, is a bona-fide 70cc saw. At 73.5cc, I look at the 575 as a "tad under 75cc" saw. I am beginning to hear limited feedback from people who have seen and run the "new edition" 575 and so far they are very positive. I would actually expect nothing less and I look forward to running one myself before I pass true judgment.

I say try them both out and see which one you like best. You certainly won't be making a mistake if you choose one over the other. I'm just pointing out attributes on both models which I have experienced.

If I was in the market for a new Husky, planned to keep it stock, Husky delivers on what they say, and be happy with my decision, I would have no reservations about choosing the new 575. Now, of course, thats a big "IF."

Just my .02 cents.

Happy Cutting!

 

[Longwood]

372xp without a doubt. Before I lug that 575xp around I would get a 390xp so I would have some power with that weight.

 

[brncreeper]

Don't know if you pulled the trigger yet, but here are some of personal observations. I own and run both a Jred 2171 and a Husky 575XPG (old edition). Both of them perform both superbly and reliably. After spending some quality time with both, it is my opinion that the 575xpNE (or whatever it is called) will be an improvement over the 372XP.

I can hear those arrowheads whistling through the air So hold on.

I know that the 575xp has received alot of bad press here but there are ample owners/members who do like them. Let me reiterate that the 372xp/2171 are fine saws and their reputations are etched in stone. Period. A chainsaws' fit to an individual operator is very subjective and I like to run a saw with a beefy chassis. Here's why I feel the 575 WILL be an improvement
.
1. I think it was Andysunshine77 who mentioned build quality of the 575 and i could not agree more. The 575 is put together real nice with excellent fit and finish. The proof is in the details and I actually see many design elements of the 385/390 filtered down into the 575. This is obviously where the weight issues come into play. The following are parts which I noticed on the 575 which are shared with the 385 family saws: air filter, clutch cover, and increased diameter handle. With regards to the air filter, I am referring to low-top models. I am assuming that the HD filter setup would be the same filter also. If one wanted to install a full wrap handle setup on the 575 you have a similar/same(?) bolt pattern shared with the 385. On my 2171, the bolt pattern is staggered. Never took the time to investigate the ipl's, but maybe the 575 has a larger clutch?

The decomp button is very well placed and has nice little rubber grommet to keep dirt out. I also like the plastic grip on the rear handle. As I said, its all in the details.

IMO, the ON/OFF/Choke setup is a huge improvement over the 372/2171. I am not alone when I say that I had my original 2171 switch fail and needed replacement. Surprised me when I found that the new replacement was stamped "Made in Germany." I have to admit that the new setup looked flimsy in pictures. I was first exposed to this setup on my 2153 and was pleasantly surprised. Very user-friendly and Husky molded the plastic around the controls just right (good protection).

2. Performance and handling. With regards to handling, I give the 372 the edge. I am sure sure that other owners will agree, very maneuverable for a 70cc saw. Stock, broken-in, and tuned properly, the 372 just flat out flies with that nice, crisp throttle response. Modding the 372 puts it into another league. The 575, as you would expect, a bulkier saw to maneuver. Tough to describe in words but this strato engine kind of detracts me a little from the engine, if you will. Almost like "throttle by wire." Not necessarily a bad thing, just different from what one is normally used to. That said, the 575 has plenty of power, particularly in the low end. Strong performance. I have actually had 32" bars on both saws and if I had to pick a powerhead to to drive those extra drive links, its the 575.

Starting procedure on either saw has never been an issue.

Fuel economy? 575 hands down. I am still amazed at the amount of work this saw can accomplish on 1 tankful of mix.

Also, for those that care about heated handles, the 575xpg gets those handles nice and toasty quicker than my 2171WH. How much quicker? Enough to notice.

Back to my original statement that the 575 "will" be an improvement over the 372. The 372, to me, is a bona-fide 70cc saw. At 73.5cc, I look at the 575 as a "tad under 75cc" saw. I am beginning to hear limited feedback from people who have seen and run the "new edition" 575 and so far they are very positive. I would actually expect nothing less and I look forward to running one myself before I pass true judgment.

I say try them both out and see which one you like best. You certainly won't be making a mistake if you choose one over the other. I'm just pointing out attributes on both models which I have experienced.

If I was in the market for a new Husky, planned to keep it stock, Husky delivers on what they say, and be happy with my decision, I would have no reservations about choosing the new 575. Now, of course, thats a big "IF."

Just my .02 cents.

Happy Cutting!

Good post.

 

[SawTroll]

hey troll, its a long story opcorn: opcorn: opcorn:


id tell ya all about it but it would end up on AS!!!

It wouldn't, if you told me not to.........

Hay Steve, you have to make friend with Spike, if you haven't already.....


:yourock: :biggrinbounce2:

 

[lazermule]

Just tried out my new 372 xp yesterday

So I got a chance to try out my new 372xp yesterday as I cut up a half cord of firewood. Wow, this is quite a saw! My old saw is an old 61 rancher and it worked well, but this new 372 is in a whole different league. I was cutting fairly green, red oak and was amazed at the power of this saw. It seemed like it was getting faster as I went as it may have been breaking in.

I have never tried a 575 so I can't comment on that. I did consider both though when I bought the 372 based on the majority of recommendations on this site. So far I am very impresssed.

 

[Tzed250]

Congratulations!!! Once the sickness sets in you will be compelled to go get the 576XP also...

 

[Longwood]

So I got a chance to try out my new 372xp yesterday as I cut up a half cord of firewood. Wow, this is quite a saw! My old saw is an old 61 rancher and it worked well, but this new 372 is in a whole different league. I was cutting fairly green, red oak and was amazed at the power of this saw. It seemed like it was getting faster as I went as it may have been breaking in.

I have never tried a 575 so I can't comment on that. I did consider both though when I bought the 372 based on the majority of recommendations on this site. So far I am very impresssed.

Congrats on the 372. Most versatile saw I've ever used. Mine puts smile on my face also.:greenchainsaw:

 

[lazermule]

I was just thinking to my self today when I walked into my shop "Where did all of these saws come from"?

Definitely is a great saw (the 372). I'm sure the 576 is a good unit as well. Maybe I will have one of those as well someday, I just chose the 372 because of the great following it has and it seems that there are a lot of parts and such readily available for it and a lot of tips and tricks because it has been around for awhile.

Lazer

 

[tommymacher]

I was wondering if anyone out there knew more about the 575's problems, I just bought one ( before I seen all the bum reports on this site) But I was wondering if there was any steps to take, besides selling, to make it hold up like I hope it will. any more info on the recall they had with bearings? before/after any certain serial #?
Thanks.

 

[gunnar]

Does anyone know when the 576xp will be on the shelves? I live in ne pennsylvania. I've also read some people are saying it will be lighter then the 575, is this true and how much?

I also bought the 575 before i found this site. So far I like the saw, but don't have anything to compare it to, because i never owned a saw this size. A lighter saw would definately be a plus. Deciding whether or not to sell mine and get the 576 when it comes out. Do dealers take trade-ins? I'm new to the saw world...but getting addicted fast.

thanks.....

 

[SawTroll]

I was just thinking to my self today when I walked into my shop "Where did all of these saws come from"?

Definitely is a great saw (the 372). I'm sure the 576 is a good unit as well. Maybe I will have one of those as well someday, I just chose the 372 because of the great following it has and it seems that there are a lot of parts and such readily available for it and a lot of tips and tricks because it has been around for awhile.

Lazer

I am pretty sure the 576xp will be a very good one - they must have got all the bugs out at this point.........

 

[peter399]

I have talked to husky and they don't do exchanges on saws,only repairs, i might as well have talked to the wall.

I told husky if it doesn't get fixed this time i am switching to a johnny, and I think I am going to switch!

tree dude

I just read some early posts in this thread. This one is funny. Threatening Husky to switch it for a Johnny