Swap meet...

[northwest coast]

076 parts

hi im looking for a pot and piston for a stihl 076

also, if anyone is selling a good quality chain grinder i'd like to buy one.

i could offer some husky parts to trade, or cash. thanks

 

[Mike Schuck]

dogs

Of all my 9xx jreds and parts saws i've had only 2, maybe 3 have an inside dog. None have an outside. All of mine have been east coast saws. Keep looking though, they're out there.

Thanks will keep looking

 

[cbfarmall]

Put a hurtin' on my 084 earlier this week. Going to need a few parts--Good fuel tank, coil wiring to the switch, HD air filter base w/oiler button and spring, and all the pieces for the rear handle; i.e. switch/lever, handle molding, tank vent. Pretty much the whole tank assembly. What a mess. Inadvertently put it near my generator exhaust and melted the whole bit. Saw is too nice to pass along as parts.

Got alot of 031/045 parts, a few 075/076 parts and that green stuff.

Chris B.

You call off the search. I got all the parts, will be assembling this weekend.

Chris B.

 

[bergman 501]

need a gas tank for an old mac 300 or ?

 

[wigglesworth]

Im in need of a 262xp carb, intake and filter if anybody has one. I have lots to trade.

 

[Jack_Shaft]

Seeing as I totally ruined my project saw today... I am looking for a 262XP builder. Need not be pretty, in theory I could still build a saw if I had a good case and crank to start with.

Any leads greatly appreciated. Yes I am already trying to win the one that's listed on eBay.

 

[epicklein22]

Looking for a top cover for a Husky 44.

 

[Arrowhead]

Anybody interested in a Mac D30? It runs, but can use some minor tlc. It does not use bar oil to lube the chain, it uses the fuel mix instead. I ran it at Seans GTG last summer and the deal that lubes the chain wasn't working. Mac guru Heimannnm was there and explained how to fix it. I just have too many other projects. I'm always looking for Partner 500/5000 saws/parts. Also larger P series Pioneer parts. I'm open to anything though.

Anybody?

 

[firefighter33]

Still looking for a set of dawgs for a 394 and a high top cover and filter. And a 24" bar and chain.

 

[barneyrb]

Looking for a top cover for a Husky 44.

Get 2 because I;ve posted several times for this....

 

[huskydude]

Get 2 because I;ve posted several times for this....

44 stuff is not that easy to find, esp for a husky

 

[huskydude]

HUSQVARNA MdL 240/444 CHAIN SAW CYLINDER COVER | eBay

 

[Mastermind]

Anybody?

It would look good sitting next to the two 35s I've got on the shelf. What do you need for it???

 

[Big Dan]

Does anyone have a good 28-30 inch bar for a Sachs-Dolmar 133? I 've got bars to trade including some roller tips and a couple of long bars for Stihl,Husqvarna and Poulan. Thanks, Dan

 

[lpmfg]

Need a brake assembly minus the brake handle itself for a jons 920

stihl 056 mag piston and muffler

stihl 026 parts, air filter, air filter cover, clutch cover.

16" bar for sithl 026~
14" bar for husky 142

email [email protected]

 

[struggle]

Looking for a fuel tank for a Mac SP 125

and dawg for the cover on teh SP125

I see them on feebay but if I can buy them from a member here I would rather go that route:msp_smile:

 

[Jacob J.]

Looking for a fuel tank for a Mac SP 125

and dawg for the cover on teh SP125

I see them on feebay but if I can buy them from a member here I would rather go that route:msp_smile:

Do you need the intake boot with the tank?

 

[Eccentric]

Do you need the intake boot with the tank?

He probably does.....................just to be on the safe side.

 

[epicklein22]

HUSQVARNA MdL 240/444 CHAIN SAW CYLINDER COVER | eBay

Hmm, think that will fit? Never heard of those models, looks like it would though.

I'll let you have first dibs Barney since you have been waiting....

 

[Jacob J.]

He probably does.....................just to be on the safe side.

Most likely. That's a weak point on the 125s. I have a lotsa tanks, not so many intake boots. I can spare one of each though.