Back In The Shop......Now What's On Your Bench????

[Brianlol]

And clean up the brush behind u ...
Dam twig that stop my leg payed a heavy price lol

 

[kz1000]

You better ice it down with a cold beverage and bolt that vice down

I'm on my fourth 12 ounce pill and no shoes, toes feel a little weird but still move. Thanks

 

[Brianlol]

If I didn't stitch myself it would have cost me money . I knew the log was going to roll and I was ready to step back but when I went back with the leg the branch was knifed into the ground and lifted my leg into the saw
First thing I thought of is what a dummy for not wearing my chaps and kill the twig lol

 

[bikemike]

I can tell you what's on my bench and what's not, on the bench is a just ported 365sp that runs super and a 254xp that I put together last week. Now for what is not on my bench, a 6" 20# vise that I some how knock off the bench right onto the arch of my right foot putting and end to todays play.

Where is the unlike button

 

[big t double]

Started rebuilding this saw, new piston and junk...it's getting the vac/pressure check tomorrow...carb has the bypassed accelerator pump on the s126 ala lone wolf.

 

[CFM]

It's not on the bench anymore

How did you get past the lack of high speed jet in the crab for mods? drill main? i have a 3120 i would love to make un-epa.......

 

[Mastermind]

How did you get past the lack of high speed jet in the crab for mods? drill main? i have a 3120 i would love to make un-epa.......

I add a high speed jet.

 

[CFM]

I add a high speed jet.

care to elaborate.....

 

[Mastermind]

I can do one for you if you like.

I simply add a high speed adjustment needle. I make my own needle, and install it.

 

[bigbadbob]

Added new tool storage above the bench.
I bought a couple of 2' long magnets, add a little wood and some screws. Botta boom Botta Bing done.View attachment 412206
View attachment 412207
View attachment 412208
So far I like the setup.

You must be tall,,,,
BBB

 

[CFM]

I can do one for you if you like.

I simply add a high speed adjustment needle. I make my own needle, and install it.

i may have to acquire a demo carb to try this myself.... thank you though for the insight. ive tried everywhere to get a non epa carb. i have the number and know for a fact that husky still have in stock non epa carbs, just wont release them. i even tried dealers that were outside the usa.

 

[Jeepsnchainsaws]

i may have to acquire a demo carb to try this myself.... thank you though for the insight. ive tried everywhere to get a non epa carb. i have the number and know for a fact that husky still have in stock non epa carbs, just wont release them. i even tried dealers that were outside the usa.

A watch makers lathe is great for making needles. And good luck

 

[295 tramp]

You must be tall,,,,
BBB

5'7" 7/6th
Tallness will git you a headache here.

How did you get past the lack of high speed jet in the crab for mods? drill main? i have a 3120 i would love to make un-epa.......

98 model stock no mods no high neddle.

 

[bigbadbob]

5'7" 7/6th
Tallness will git you a headache here.

Was wondering as I can reach 8ft4in ,,, your shop looked like a good stretch.
BBB

 

[Mastermind]

There's parts of five MS261s in these boxes.

I reckon I do more 261s than any other saw.

 

[SS396driver]

Not on the bench yet 390 AMC out of my 69 AMX.. Bad wrist pin knock

 

[bikemike]

Not on the bench yetView attachment 412378 390 AMC out of my 69 AMX.. Bad wrist pin knock

Nice dual quads. Whats the car look like. They made some bad azz drag cars back in the days

 

[redfin]

Wooooooooot!

 

[Mastermind]

There you go John.

Please don't take all my work now.

 

[bikemike]

Wooooooooot!
View attachment 412385

Woot woot. Where did you order that from? And how much. Is the 1/8 inch