New Oregon Narrow Kerf Chain and SpeedCut Guide Bars

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
......
The Carlton/Woodland Pro chain probably will last in softwood, but the stuff I cut gives it a hammering. One other problem with the Carlton chain is the heel of the cutter. The heel comes to a sharper point and creates a greater loading on the bar rail. I noticed increased bar wear when using the Carlton chain. The VP95 chain has a broader heel and spreads the force over a larger area.

..... .

That's because Carlton doesn't have a low-vibe chassis, that was invented by Oregon and later adopted by Stihl.

This is quite odd, as Carlton has the same owner as Oregon, and they do sometimes cooperate....
 
I went back and re read a bunch of stuff in this thread.
Replacing the entire pro lite with this technology, they changed naming lately so complicating stuff I suppose this means SL and GL in standard and MP in narrow kerf. The lower grade dual guard, pro am, microlite without the pro (ML) will stay the same at least for now? Does what I read mean they are offering NK bars in more than 10 tooth noses? From the look of the picture in post 35 that 20% could be for a large, 12 I guess tooth nose with 0.063 middle lamine couldn't it? That is for speed cut, versa cut, and control cut. I see nothing about improvement in plunge cutting.
 
l have some .043 oregon nk semi chisel that really performs well. Small cutters but smooth and fast which is what you need on a polesaw.

That Oregon Type 90 chain is surprisingly aggressive if sharpened with the 4.5mm / 11/64" file. I have it on their 40V pole saw and it works really well.

Philbert
 
Yes, that's why I specified that the Husky bars are K095. It should be possible to adapt them, as they are K-tail bars?

I suspect that a 20" bar isn't a good idea on an Echo 490 - but it will of course work.


Yea I would think the old grind the adjuster opening till it breaks through the underside of the bar groove would work to use the K095 mount on the Echo. My point of contention is why the K041 style mount is not listed for the new NK bars? Tons and tons of saws use that mount.

Another thing is what is the point of the new K216 bar mount? Basically a K041 with a oil hole...

If you want to go there, a 20" bar on most 50cc saws is not a great idea. If you are going to use a 20" bar on a 50cc saw, I think the NK setup is a good idea.
 
Yea I would think the old grind the adjuster opening till it breaks through the underside of the bar groove would work to use the K095 mount on the Echo. My point of contention is why the K041 style mount is not listed for the new NK bars? Tons and tons of saws use that mount.

Another thing is what is the point of the new K216 bar mount? Basically a K041 with a oil hole...

If you want to go there, a 20" bar on most 50cc saws is not a great idea. If you are going to use a 20" bar on a 50cc saw, I think the NK setup is a good idea.

I don't see the point with the K216 mount either, unless it just is to sell more OEM branded bars, by being different.

What kills my interest in the NK bars mainly is the lack of a good chisel option. If that isn't an issue to the user, I agree that NK is a good idea.
 
I don't see the point with the K216 mount either, unless it just is to sell more OEM branded bars, by being different.

What kills my interest in the NK bars mainly is the lack of a good chisel option. If that isn't an issue to the user, I agree that NK is a good idea.


I was thinking the same thing on the 216 bar mount, being a way to sell more OEM bars but Oregon sure does have plenty of that mount in there catalog, just not in the NK style.

I know your opinion on needing a full chisel cutter in NK and I agree the choice would be nice but then again it depends what your cutting. I in the past used the 95VP chain on a bunch of firewood cutting and what I was cutting I would not have wanted a full chisel cutter as we were cutting out of brush piles etc so not the cleanest wood.

To be honest, the 95VP on my Husky 350 I was using at the time seemed as fast even in clean wood as the 20Lp so I don't feel at a loss not having a full chisel option in the NK chains.
 
To be honest, the 95VP on my Husky 350 I was using at the time seemed as fast even in clean wood as the 20Lp so I don't feel at a loss not having a full chisel option in the NK chains.
Quick question on this. Does the same sprocket work with standard 3/8 and 3/8 low profile for these saws or is there a different one for low profile?
 
Quick question on this. Does the same sprocket work with standard 3/8 and 3/8 low profile for these saws or is there a different one for low profile?

Info page says that they 'fit .325”-pitch, standard 3/8”-pitch, and .404”-pitch chains'. Do not mention 3/8 low profile. Their spur sprockets specifically mention 3/8 low profile.

http://www.oregonproducts.com/pro/products/sprockets/sprockets_powermate_system.htm

http://www.oregonproducts.com/pdf/sprockets/RimSproxFB0601.pdf

Philbert
 
Quick question on this. Does the same sprocket work with standard 3/8 and 3/8 low profile for these saws or is there a different one for low profile?


They are different, as the lo-pro/picco needs a larger rim to compensate for the low profile chain chassis. The bar sprockets are different as well.

Oregon doesn't offer lo-pro rims, that's why they don't show up in the link.
 
On the Oregon website:
https://www.oregonproducts.com/pro/products/chain/95TXL.htm

95TXL Chain
Work faster, sharper, easier, with a more efficient chain. Ideal for arborists and property owners who want top performance. 95TXL is for saws up to 55 cc. (Replaces 95VPX.) SpeedCut™ 95TXL narrow kerf cutting systems are more efficient, needing less power from the saw than standard cutting systems. Low-vibration, Micro Chisel cutters have small-radius working corners for excellent performance and easy maintenance. Get a faster, easier cut with a reshaped cutting surface. A sharper, more durable cutting edge from a new precision grind and optimized cutting angle. Always use SpeedCut narrow kerf chain in combination with SpeedCut or Micro-Lite bars.

ProductDetail_BlackDot.gif
.325" pitch, .050" gauge
ProductDetail_BlackDot.gif
95TXL chain is intended for use with gasoline-powered saws up to 55 cc with bars up to 20" (50cm).


Philbert
 
Oregon told me too contact my norwegian oregon dealer, I did he is going to send me the oregon speed cut bar and chain as soon as he get them for free so i can try them out, very nice. He expected to have the chain and bar in the summer of -16
 
Back
Top