Want to Sell Bars and bars and bars still some left!

[astnmacgto]

Have a lot of different bars of all shapes and sizes, I do believe they mostly what they call the small husky or jonsered mount but I can't prove it.
Majority are new, some in the package, some new, and some dirty but still new, if you see a bar you think you can use message me and I will send you part numbers off them. Most bars are gonna be in the $10 to $15 dollar range, some just a little bit more and there are couple that will be free. Thanks for looking!
ADLM

 

[astnmacgto]

Mores pictures, they are in sets of three.
Whole bars
Mounts
Tips
Also just wanted to throw out the fact that I would probably trade for mcculloch parts or bars.

 

[Flymesouth]

if they're k095 mount and 3/8 x .050 and you have 'em i'll take a 16 and 18 and a 20 inch! Pm me when you know!

 

[astnmacgto]

if they're k095 mount and 3/8 x .050 and you have 'em i'll take a 16 and 18 and a 20 inch! Pm me when you know!

Get me specs on a k095 mount and I'll be glad to let you know

 

[Flymesouth]

k095 is small mount husky. but I'd need 3/8 by .050 that said if you've the three I'm lookin' for 3 are sold haha. As for specs...#'s vary by manufacturer! So without being in front of the bars I'd not be able to decifer the #'s.

 

[astnmacgto]

k095 is small mount husky. but I'd need 3/8 by .050 that said if you've the three I'm lookin' for 3 are sold haha. As for specs...#'s vary by manufacturer! So without being in front of the bars I'd not be able to decifer the #'s.

Just looked only 3/8 50 I have is a large mount total bar, only other 50GA are 325, I'll look to see I'd I have anything in a different bar perhaps

 

[jakethesnake]

Nice stash of bars man I can get a measurement of bar studs if that helps you move these

 

[jakethesnake]

@Flymesouth if you need a bar the .050 won't matter They will still fit the sprocket or rim you intend to use you'll just have to grab up the correct chain to fit the bar groove. If you already have the chain the bar won't work for you You could also change up your rim sprocket to run .325 I have done that with a few saws I prefer the .325 on saws under 50cc what saw are you trying to run these bars on?

 

[jakethesnake]

What lengths do you have in the large husqy mount I may take one or two. Thanks

 

[Flymesouth]

I've 3/8 x .050 chains for my lil' rancher coming out my ears jakethesnake and since its now been relegated to a small saw I'm kinda unwilling to swap out chain sizes, but duly noted.

 

[astnmacgto]

A lot of the stuff I have is 325 58 or 3/8 lo pro 58, I have a total II bar that's 22.5 inches end to end and 19" tip to front of bar mount it's 3/8 50, the jakmax is large mount I do believe it's 3/8 63 it's 23" overall and 19" tip to front of the bar mount, and the husqvarna is a 3/8 58 bar 72 drivers

 

[jakethesnake]

I've 3/8 x .050 chains for my lil' rancher coming out my ears jakethesnake and since its now been relegated to a small saw I'm kinda unwilling to swap out chain sizes, but duly noted.

Well if you have a set length of chain say 64 dl 50 3/8 And were looking for a bar 20 inch and it took 3/8 .058 72 drivers you could still use that without changing up anything. Hope that helps someone out here

 

[jakethesnake]

I've 3/8 x .050 chains for my lil' rancher coming out my ears jakethesnake and since its now been relegated to a small saw I'm kinda unwilling to swap out chain sizes, but duly noted.

Well if you have a set length of chain say 64 dl 50 3/8 And were looking for a bar 20 inch and it took 3/8 .058 72 drivers you could still use that without changing up anything. Hope that helps someone out here

 

[Matt_Ellerbee]

Any 3003 Stihl mount 18"? Shipped to 30115,Ga.

 

[jakethesnake]

The total 11 large mount I'd be interested in have any longer or is that about as big as they get?

 

[Red97]

What is the slot size on the ones with the square adjuster holes? If those are d176/196/uxl mount? lengths/pitch/gauge please.

 

[astnmacgto]

I feel like I a bomb went off already haha, I will do my best to get everything sorted out for all of you that have given me specs to go off of, I'm already in for the night so I will do some measuring tomorrow and Wednesday and get back to all of you. Thanks for all the inquiries
ADLM

 

[Boomer 87]

I want the poulan control tip, short black one. Bring it to work tomorrow

 

[astnmacgto]

I want the poulan control tip, short black one. Bring it to work tomorrow

Well you ain't getting any special deals, haha, who do you think you are, family?

 

[Boomer 87]

Whatevs