jrider
Addicted to ArboristSite
I’m sure it does and odds are at least 1 if not more chains out of 12 would need a little tlcDepends if its just dull or rocked I suppose. Prob takes a bit longer than 5 minutes though.
I’m sure it does and odds are at least 1 if not more chains out of 12 would need a little tlcDepends if its just dull or rocked I suppose. Prob takes a bit longer than 5 minutes though.
Every timeI’m sure it does and odds are at least 1 if not more chains out of 12 would need a little tlc
Almost without fail!Every time
Everytime I put on a new chain I hit nails.
Most of the chains I use are second-hand from auctions and cost me just a few bucks a loop (luckily a lot of users don't know sh.. about chain maintenance). Also, I don't mind if a few teeth are shorter than the others when hand-filing as the longer ones will catch up over time. To me the most economical way to use up a chain while making it last.
Matching the length of all teeth to the shortest tooth is a waste of material imho... However, I do understand that a grinder is a very time-efficient tool for people that get paid for sharpness by time
That's what hand-filing is all about. Doing each tooth individually and adjusting raker height (depth) according to tooth height whenever necessary. With a grinder there is no way to do that.Agree, there is no need at all for every tooth on any chain to be the exact same top plate length- but the raker should match the corresponding cutter.
An 84 tooth dull chain on and off the vise in 5 minutes. I would like to see 12 done in an hour
Ok, so a bit of an exaggeration. But you can eliminate the vice step, for one. Just sharpen on the bar...
I get that but who has 12 full chains on saws at one time?Ok, so a bit of an exaggeration. But you can eliminate the vice step, for one. Just sharpen on the bar...
I get that but who has 12 full chains on saws at one time?
Yep. It ain't the grinder that 'ruins' a chain, it is the operator that 'ruins' the chain, using the grinder as their weapon. I can 'ruin' a new chain with a file in 3 strokes or so, if I am determined. In fairness, the instructions that come with most grinders are . . . inadequate. Took me a long time to figure stuff out, and I try to share that with others, if they are interested.Sure you use a file on site to touch up a chain if needed but, they sure cut smooth after a good grind. It sucks to see so many people that grind wrong.
I have picked up a number of loops for 50 cents each at estate sales, usually after they have sold the saw(s) that went with them. Sometimes free. Having a spinner / breaker set means I can be less picky about DL count.Most of the chains I use are second-hand from auctions and cost me just a few bucks a loop . . .
Helps the chain cut smoother: equal cutter height (saw 'jointing') and side projection / kerf width (saw 'setting'). If that does not bother you, than it is not an issue.Matching the length of all teeth to the shortest tooth is a waste of material imho...
I like a chain that is held solid, so that I can control a sharp file with both hands, and not have to deal with rocking / moving cutters. That said, in the field I sharpen / touch up on the bar, but I like it held securely, like with a stump vise, or by boring into, or slotting a log, to hold it. I don't like assuming some yoga contortion to hold it.Ok, so a bit of an exaggeration. But you can eliminate the vice step, for one. Just sharpen on the bar...
....... boring into, or slotting a log, to hold it. I don't like assuming some yoga contortion to hold it.
I can always tell what customers of mine handfile their chains. Complaints of rough cutting, leaving a coarse face in the cut, being boggy, pulling to one side...so on.
With a grinder...every tooth is the same dimension, same angle, same depth. Sure you use a file on site to touch up a chain if needed but, they sure cut smooth after a good grind. It sucks to see so many people that grind wrong. Ive got a customer with an MS290 with a 20" bar i put on an archer chain for him. He cuts 3 tanks of gas and brings it to me to grind about every 3 days. Ill get at least 15 grinds out of it before we retire it and thats with him touching it up between tanks...you just kiss the cutter and sweep the gullet, barely any heat and just a light spark. I get chains in from other shops and the cutters are blue, nicks in the straps, half the cutter gone and it was only sharpened once.
Sent from my LM-G820 using Tapatalk
I usually have 10-12 chains that I swap outYou don’t carry spare chains with you? Or do a weeks worth at once? Running the harvesters we can go through 15 in less then a week and I’m sure not going to hand file one of those especially on the head.
Sent from my iPad using Tapatalk
Enter your email address to join: