drf255
BAD CAD
Do I run a huge risk if I just put some fuel in the intake boot?
Think I'm wimping out and dissembling it.
Think I'm wimping out and dissembling it.
MS250-Too Much Compression?
- Thread starter drf255
- Start date
Help Support Arborist Forum:
wigglesworth
Booned
Do what makes u comfortable.
And that's a big no on firing it off with no carb. She'll sing to the moon!!
nmurph
ArboristSite.com Sponsor
...and you're not losing 30-40psi from cold to hot. It's more like 10-15psi.
I doubt he timed it if he's asking about "taking 1-2mm" of the exhaust to reduce compression (yes, that will reduce compression...).
I doubt he timed it if he's asking about "taking 1-2mm" of the exhaust to reduce compression (yes, that will reduce compression...).
drf255
BAD CAD
It's coming apart. This is my 3rd 025/250 rebuild. Got it down to the tank and motor in under a half hour.
I Dirko'd the hell out of it. Even around the seals. The cleanups gonna be a beoch.
It's a "good saw" to me. I want performance, but also something that lasts.
I'm gonna try to get it down to the 180-200 psi range.
The ports have been played with already, just squared, enlarged and blended. I didn't mess with the timing.
This time I'm testing compression BEFORE I glue the engine back together.
For those who wanted to see it explode, sorry.
Sent from my iPad using Tapatalk
I Dirko'd the hell out of it. Even around the seals. The cleanups gonna be a beoch.
It's a "good saw" to me. I want performance, but also something that lasts.
I'm gonna try to get it down to the 180-200 psi range.
The ports have been played with already, just squared, enlarged and blended. I didn't mess with the timing.
This time I'm testing compression BEFORE I glue the engine back together.
For those who wanted to see it explode, sorry.
Sent from my iPad using Tapatalk
D
Deleted member 83629
Guest
good luck.
drf255
BAD CAD
It's out
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
drf255
BAD CAD
Sent from my iPad using Tapatalk
You said you "Dirko'd the hell out of it". I'm not trying to split hairs, just curious; All of the Dirko I've ever seen is red & your sealant looks grey. Is it actually Dirko, or something similar?
drf255
BAD CAD
It's dirko. The one I bought grey.
That's interesting, I wonder if there's a difference between them?
You will not get an accurate compression test until it has been run to clean the assembly lube out of it.
You're missing a very critical part. Until you degree that cylinder, and put the port timing where it should be, you're leaving a huge piece of the pie out of the equation. The transfers likely need raise, and the intake probably needs lowered. You will see gains for your port widening, but not what it could be. You can print out a paper degree wheel, sized to the diameter of your flywheel, and then simply glue it onto the fins. Make sure it's centered and that will be plenty good enough. Let us know what your stock port timing is and we can go from there.
drf255
BAD CAD
I don't have the knowledge you do Brad. I figured I'd worsen whatever the engineers calculated more than I'd help.
It's also a clamshell with very long and thin transfer ports. Not the typical ones with an entry and exit.
I'm reading Jennings books now. I have a 12" automotive degree wheel. I need to make an adapter.
I do sincerely appreciate all the advice you've given.
Just glue a degree wheel onto the flywheel. There's no need to go to the trouble to make an adapter unless you plan on doing more saws.
drf255
BAD CAD
Reduced dome.
Gonna rebevel ports.
Keep ring gaps at .008 or open a bit?
Sent from my iPad using Tapatalk
Gonna rebevel ports.
Keep ring gaps at .008 or open a bit?
Sent from my iPad using Tapatalk
drf255
BAD CAD
Sent from my iPad using Tapatalk
Leave the rings as they are.
drf255
BAD CAD
Thanks. I rechamfered my ports.
Sanded piston from what you saw above. Blended any hot spots.
With an oiled cylinder, I'm at 210 psi now.
Sanded piston from what you saw above. Blended any hot spots.
With an oiled cylinder, I'm at 210 psi now.
