Swap meet...

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Need Husky and Stihl Parts!

Needed for a Husky 288xp
-Recoil cover (prefer complete)
-Top cover (prefer high top, but beggars can't be choosy)
-On/Off Switch with wiring harness

Needed for 044
-Chain brake handle
-Top handle
-Recoil cover (prefer complete)
-Muffler
-All top plastic

I have two Husky 257's for trade. Both complete, one runs, and one is questionable. I have pics I can send.
Or of course, green.

Thanks in advance.

BBB
 
XL-12 pics.

attachment.php


attachment.php


attachment.php


attachment.php


You weren't kidding about it being clean. You should hang on to that saw.
 
Will, that old XL-12 is too old to have the electronic ign anyway...

Ahh, thanks. I know nothing about these saws.

You weren't kidding about it being clean. You should hang on to that saw.

Ya it is clean. Maybe one day I'll get around to it. Likely needs just a fuel line and filter, and ignition gone through. I think the rash that it has on it is from being moved around, there is seriously no sawdust anywhere on this thing.
 
Need Homelite 240 parts

Homelite 240 parts needed
Air filter
Filter cover with hand guard
Fuel/oil tank
AV buffer parts for recoil side of the wrap handle, I have the rubber bushing
Square nut for the inside of the recoil, for the above AV buffer.

I have a box of Husqvarna 50/51/55 parts
Like new crankcase from a 50 special w/ flywheel, oiler, spikes and oil cap
Model 50 filter plate, filter and intake
Flywheel
Clutch with .325x7 rim
bucking spikes
Complete oiler with bar plate
51 cylinder that needs honed
50 cylinder that needs honed

Also have a muffler off a husqvarna 2100 that I know fits other models also.
New 404 tip for a Oregon Power match bar, no rivet

PM with what you will need for the parts.
http://s647.photobucket.com/albums/uu193/Roanoker494/Chainsaw parts/
 
240 parts

Homelite 240 parts needed
Air filter
Filter cover with hand guard
Fuel/oil tank
AV buffer parts for recoil side of the wrap handle, I have the rubber bushing
Square nut for the inside of the recoil, for the above AV buffer.

I have a box of Husqvarna 50/51/55 parts
Like new crankcase from a 50 special w/ flywheel, oiler, spikes and oil cap
Model 50 filter plate, filter and intake
Flywheel
Clutch with .325x7 rim
bucking spikes
Complete oiler with bar plate
51 cylinder that needs honed
50 cylinder that needs honed

Also have a muffler off a husqvarna 2100 that I know fits other models also.
New 404 tip for a Oregon Power match bar, no rivet

PM with what you will need for the parts.
http://s647.photobucket.com/albums/uu193/Roanoker494/Chainsaw parts/

I should have all the parts you need for the 240, but don't need any other parts for Husqvarna's at this time.
4000fixed
 
1-70 clutch

Wanted....Mac 1-70 clutch side starter pawls w/springs...Im going nuts...I just got this saw and i cant find out if it runs or not...
Looking to buy

I think I have 1 good used complete clutch left. You can private message me for details.
4000fixed
 
McCulloch 890 36" .404 bar needed

Hello,

I'm looking for a bar for a McCulloch 890 .404 in case anyone happens to have one laying around. Or perhaps a roller tip for the above bar.
 
Needed

Muffler for Homelite C72
Muffler front cover Stihl 038MAGII
Air filter and cover for Homelite 330
Wrap for Stihl 064

Have parts or Green to trade.
 
I'm needing a good crank or bottom end for a stihl 009. I'm still trying to round up the parts to put my friend's saw back together. I've got stuff, or cashola.
 
I got 12' left of a roll of the Oregon 3/8" power sharp stuff, like used on the old power sharp craftsmans and poulans. Trade for Green or ???
 

Latest posts

Back
Top