RED-85-Z51
Addicted to ArboristSite
Going to be groundbreaking my new Storage shed in a couple weeks, 40X14. In it, I will finally be able to store my Vintage GT's, and Ill have shelving and hangers for all my good saws and stuff.
I want to be sure all my decent/good saws are in working order when I get done, so I took a look at the stuff at the front side of my current falling down tin shed...
The 350 cranked up, CS-520 cranked up, Tanaka cranked up, couple of the poulans cranked up too...that's about the extent of it. Keep in mind they've been sitting probably 9 months to over a year in some cases.
The 025 needs a fuel line..it's cracked, also there is a little hole next to the muffler, in the side of the case that pours out oil when I run or tip the saw...Am I missing a plug or a vent?
MS-260, I need to order the P&C from Baileys.
MS-260Pro- need to bring home from work and see if I cant clean up the piston and cylinder
Homie XL, Super2, Super XL, etc..Got 2 good motors, 2 good fuel tanks, 1 good recoil, 2 good mufflers, and no good carbs...Got to take em all to work over the Winter and make a coupel good saws. One of these (the XL) My father bought new in 1968, and it ran flawlessly until the fuel tank bottom rubbed thin and cracked.
Mac 160S...Awesome saw, got a good coil to put on it to make it run again, too hot to mes with putting it together right now...what a pain those are.
Mac 4618- Got to order the dang intake boot, this saw only has about 4-5 minutes on it, total.
Wizard BO-13 (poulan 3700) I found a mint parts saw at work, burnt piston, but it has the carb I need...Winter project.
Wild Thing- Needs a Chain, cranked on 3 pulls...I was kinda shocked by that one.
Thats pretty much all I could get to...but at least I wont be bored this Winter, and Ill finally have a place to display my saws.
Cant wait to get the new shed underway...Not looking forward to building it.
I want to be sure all my decent/good saws are in working order when I get done, so I took a look at the stuff at the front side of my current falling down tin shed...
The 350 cranked up, CS-520 cranked up, Tanaka cranked up, couple of the poulans cranked up too...that's about the extent of it. Keep in mind they've been sitting probably 9 months to over a year in some cases.
The 025 needs a fuel line..it's cracked, also there is a little hole next to the muffler, in the side of the case that pours out oil when I run or tip the saw...Am I missing a plug or a vent?
MS-260, I need to order the P&C from Baileys.
MS-260Pro- need to bring home from work and see if I cant clean up the piston and cylinder
Homie XL, Super2, Super XL, etc..Got 2 good motors, 2 good fuel tanks, 1 good recoil, 2 good mufflers, and no good carbs...Got to take em all to work over the Winter and make a coupel good saws. One of these (the XL) My father bought new in 1968, and it ran flawlessly until the fuel tank bottom rubbed thin and cracked.
Mac 160S...Awesome saw, got a good coil to put on it to make it run again, too hot to mes with putting it together right now...what a pain those are.
Mac 4618- Got to order the dang intake boot, this saw only has about 4-5 minutes on it, total.
Wizard BO-13 (poulan 3700) I found a mint parts saw at work, burnt piston, but it has the carb I need...Winter project.
Wild Thing- Needs a Chain, cranked on 3 pulls...I was kinda shocked by that one.
Thats pretty much all I could get to...but at least I wont be bored this Winter, and Ill finally have a place to display my saws.
Cant wait to get the new shed underway...Not looking forward to building it.