550xp Dawg Mod

I decided to put the factory 562xp dawg on the 550xp for a little more extension. Here's a couple pics.

550xp/left 562xp/right


And installed after a slight inner elongation of the mounting holes with a 3/16" file. 562xp dawg P/N 577 97 52-01

That is killer Jeff!

Nice

How about dual dawgs for it :msp_wink:

H 2 H said:

Nice

How about dual dawgs for it :msp_wink:

Click to expand...

Saw Troll would be upset with me! :msp_biggrin:

Joe Kidd said:

Saw Troll would be upset with me! :msp_biggrin:

Click to expand...

:surrender:

I know with a different brand 50 cc saw that has dual dawgs you can lay the coals to it and get a huge bit while bucking firewood :msp_scared:

Nice work, looks good.

Mine looks just like that except more dirtier.. Termite

TermiteBuffet said:

Mine looks just like that except more dirtier.. Termite

Click to expand...

I cleaned em' up for the fashion shoot.

Ok first post using tapatalk someone give the kindergarden version on how to get the pic to show up without having to open it..... Sent from my C771 using Tapatalk 2

TermiteBuffet said:

Sent from my C771 using Tapatalk 2

Click to expand...

That looks familar!

Hey , Jeff will that hole hold a roller chain catcher ????? HMMMMMMM

TermiteBuffet said:

Ok first post using tapatalk someone give the kindergarden version on how to get the pic to show up without having to open it..... Sent from my C771 using Tapatalk 2

Click to expand...

Tell ya the easiest way...for me.

Get a photobucket account. Upload straight to photobucket from a smart phone with a push of a button. Then copy and paste it right here using photobuckets image code.

Ok I'll tell ya; I do blow (with a air compressor) my saw's off and wipe them down including clean bar and bar grooves after using them for hours on end. I just can't wait for that Earthquake to get here :jester:

TermiteBuffet said:

Hey , Jeff will that hole hold a roller chain catcher ????? HMMMMMMM

Click to expand...

Should. I done basicly the same thing to my 346xpne. Took a stock dawg off a 372, slotted 1 hole and mounted it on the 346 with the roller chain catcher. Even served as a kickstand too .

TermiteBuffet said:

Hey , Jeff will that hole hold a roller chain catcher ????? HMMMMMMM

Click to expand...

It looks like it should. I'd have to check the stud dia.

I need to do better cleaning up ,i cut till dark this evening i was hungry , sweaty , and getting chilly, komatsuvarna, i like that idea for the 346 kickstand, mine loves to roll over and play dead :msp_biggrin:

komatsuvarna said:

Should. I done basicly the same thing to my 346xpne. Took a stock dawg off a 372, slotted 1 hole and mounted it on the 346 with the roller chain catcher. Even served as a kickstand too .

Click to expand...

SWEET

I would really like to run one with dual dawgs to get a real good bit in a log :msp_biggrin:

I ran with the 562 dowg for a while and I wasn't any more impressed with it the. The stock 550 dowg so I designed one that I would like and this is what I can't up with, I also removed the stock chain catch and made a roller set up, I know I could have used a 372 pr similar roller but I couldn't find one in my time frame.

Thats nice there mx, i like

komatsuvarna said:

Should. I done basicly the same thing to my 346xpne. Took a stock dawg off a 372, slotted 1 hole and mounted it on the 346 with the roller chain catcher. Even served as a kickstand too .

Click to expand...

Did'nt that affect the sideways balance though ? :hmm3grin2orange: