Search results

Update on the status of Huztl fulfilling their warranty. I was messaging Huztl back and forth about the warranty damage and it all seemed to be going well. I purchased PJ44000 which was an engine mounted in the case halves. I paid more for the engine assembly as I did not feel confident to...

@NCPT The bar is 3003-812-6817 SA .325 .063 74 links 18”. The prior owner had this number bar on it and gave me a used bar of the same number and three new bars in packaging with the same number. The oiler hole seems to be lined up with the bar hole. I ran it with bar and chain but no cover...

1141-664-1002 Inner side plate = bar oiler plate. OK on the case picture. The tensioner area looks simple and easy to deal with. Thanks. Found some assemblies $15-$20. Huztl has them for couple of bucks. Just realized that I’m checking the interior case side i.e. behind the bar. In...

@NSEric My IPL is SCS 01-2011 3.33. Page 9 shows the plate for several models. The next page lists which models get a plate. Models 1 and 2 do not use a plate. Only model #3 for the 271. (1) MS 271, (2) MS 271-Z, (3) MS 271 C-BE. It does not have one but maybe installing one would help...

No oil getting on the bar. I think it is leaking behind the bar down to the bottom of the case. It leaks over to the spur cover and throws oil all around the inside as shown. If it runs with no bar the flow seems to be fine and leaks straight down to the base. The bar oiler hole is...

Finally got around to the 044 vent. I was not able to punch the bent into the oil reservoir. The pictures show the difficulty. Looking into the inside it looks like there are internal case parts that obstruct the vent from getting into the case. Also there is what looks like a metal flange...

I goofed on the 261-271. Below is a used set for $105. https://www.ebay.com/itm/STIHL-MS-271-CYLINDER-GOOD-USED-OEM-PART-COME-WITH-EXTRAS/123799065300?hash=item1cd2ffd2d4:g:y7MAAOSw9HNc~9cu

@SteveSr Ah! I thought it was something like a duck bill that could be prodded. The old one is out but I did not notice anything to indicate how it worked. I’ll take a closer look in a couple of days. Again the one I took out was from the original case, now scrap. The 044 with the new...

I poked and poked with a couple of thin wires that were fairly strong without success. I could get about 3/4 of the way into the vent. What ever was plugged in there seems solidly jammed. The assembly I was doing that on was the original case that got no oil scored. I'll try flushing with...

@Mad Professor I tired punching it through and hitting it pretty hard. It would only go about ¾ through then stop. If I hit harder I thought I would break the case so punched through the reservoir. That got it out. ? Not sure why it would not punch through. @atpchas OK, thanks. I was not...

https://www.amazon.com/shuihuo-Piston-44-7mm-Kolben-11410302012/dp/B01NB8SSJ4 https://www.amazon.com/Piston-44-7mm-Replaces-Quality-Reproduction/dp/B07B29BVSJ/ref=pd_lpo_sbs_86_t_0/139-3866893-3195160?_encoding=UTF8&psc=1&refRID=N1P2BYGXF0NJ1WMEM6EM...

On the 044 IPL there are two plates listed. The plate on my 044 is 32. The tabs on it are a pain when taking out the bar studs. Would switching to 31 be ok? #5 is the oiler vent. Does that come out by punching it through the case into the oil tank the way it is removed? I assume you...

@Mad Professor Me too, thanks. I expected they would eventually replace the assembly but not that it would be so easy. They never asked about anything. They just said send a list of parts. They only asked that I be careful to get the part numbers I wanted right. I’m out $125 as I paid a...

Huztl service is going to replace the engine case assembly and any other damaged parts. I’m not where the 044 is so will have to go over it closely when I get back and check for any other damage. So far I know the clutch and oiler are damaged. I goofed in other posts calling this a clam...

I got the saw out of a repair guys junk pile for $50. The engine was a customers and the guy never bothered to fix it. I got it as a project. The replacement shell and engine were an assembly from Huztl/Farmtec. The shell metal seems fine. It seems like someone flubbed in manufacturing like...

OK, so the pin coming out had to be a manufacturing defect. I think the pin is, #3 on my IPL, Cylindrical pin 5x18. What are the units of the 5 x 18?

Hole Damage by trouts2 posted Jun 24, 2019 at 7:25 AM My 044 crashed. A case alignment pin on the left side of the oiler area fell out and smashed around in the oiler area. Black oil started leaking out below the sprocket cover then the piece of clutch broke off inside and the engine stopped...