McCulloch Chain Saws

[Mo. Jim]

i have plenty of chain thanks. And your right I will sometimes call a sprocket tip a roller nose, even though I know better. It can be even more confusing to a person if a saw has a Windsor bar on it and I call it a Speed Tip. People will look at you like you have 3 heads.....

The bars i question are the non-replaceable sprocket tips. For the 12 bucks each, i just might buy a couple and hope the best.

I have some nos hardnose bars that came on some PM6's. I might part with one or two,they do have some shelf wear though.

 

[minosi]

Here I was thinking that you were a allright guy,then you call my PM6's Ugly. Those are fighting words partner.:msp_smile:

Where's Mini Mac Man so this can be a fair fight

 

[minosi]

PM 6 lovers....

View attachment 262199




For the "Old Man's Saw" project.


Couldn't get just 2 of each made!

 

[mini mac man]

Where's Mini Mac Man so this can be a fair fight

I am here! Mini Mac attack. Lol

 

[Overtrained]

Here I was thinking that you were a allright guy,then you call my PM6's Ugly. Those are fighting words partner.:msp_smile:

Maybe im just bitter cause my mini's get #### on all the time. They are perfectly good, hard to start and maintain saws!

 

[little possum]

What happened to the ignition setup That I sent you a few months ago. It had spark when I pulled it off the parts saw or is it lost in your shop some where.:msp_smile:

I switched it all over... I think.. I cant remember. haha Have to check again. I feel like I just dont have something hooked up right. It had spark before I tore it down.. But I do appreciate the parts.

 

[ChainsawmanXX]

Picked up a 1-70 today, pictures later

Sent from my LS670 using Tapatalk 2

 

[ChainsawmanXX]

Wadda think 1-70?

Sent from my LS670 using Tapatalk 2

 

[Macman125]

sp125

Where could I find a 9 pin rim for 3/8 chain for my sp125?

 

[joeymt33]

Where could I find a 9 pin rim for 3/8 chain for my sp125?

I've seen them on eBay.

 

[cpr]

Conrod bolts. Reuse or replace.

Super 797 if that matters.

 

[joeymt33]

Conrod bolts. Reuse or replace.

Super 797 if that matters.

I haven't heard of them being a "torque to yield" bolt. Maybe they can be reused.

 

[cpr]

I haven't heard of them being a "torque to yield" bolt. Maybe they can be reused.

They're not. Don't have the spec to hand right now, but 50-100 in/lbs is in the neighborhood.

 

[Macman125]

There are several different inner diameter sizes. Which do I need?

 

[joeymt33]

There are several different inner diameter sizes. Which do I need?

It should be the big one unless someone changed it. 7 spline.

 

[Mo. Jim]

I found two big ziplock bags of seals in my stash today,part #50663. Any one know what saws they might fit?

 

[Macman125]

sp125

So it came factory with large 7 spline?

 

[joeymt33]

So it came factory with large 7 spline?

I'm pretty sure, hopefully someone with more knowledge about this topic will confirm. My sp125 and sp105 had the large 7 spline.

 

[joeymt33]

I found two big ziplock bags of seals in my stash today,part #50663. Any one know what saws they might fit?

The MC91 kart engine is one model it fits. I'm sure there are many more

 

[ozflea]

Conrod bolts. Reuse or replace.

Super 797 if that matters.

Depends on how much you value your rebuild .................