New Dolmar 60cc strato saw, PS 6100
- Thread starter MotoMax
- Start date
Help Support Arborist Forum:
cuttinscott
Addicted to ArboristSite
Strato or non Strato the EPA Tag is their rating of how long they want the engine to Run Clean to EPA Standards some engines have 75 some 125 some 200 some 300 etc.
Scott
zogger
Tree Freak
True, Husky must take the blame and shame for that silly creation!umpkin2:
What is wrong with them, they just don't cut well or what? Specs say some decent HP.....
My understanding is the hour number is more like the time it can run before some pollution quota is reached. In my limited experience it effects fumes breathed and goo around the exhaust. Probably there is something similar to a fleet average in this business. The manuals I have/have read have a general section with 75,125,and 300 actually in print.
SawTroll
Information Collector
Not really decent when you consider the weigh. :msp_wink:
Hedgerow
HACK
I don't know why they made that model...
Was it a marketing idea that went afoul???
Not that they're bad, just sort of no home for them. Who would have been the targeted consumer group?
Locust Cutter
Sawing for Sanity
Is this screwdriver the female torx style one to adjust the new splined adjustment screws on the 9010 for example? I ask because my local Dolmar dealer indicated that he was forbidden from Dolmar and the EPA from providing the adjustment screwdriver(s) and could in fact be fined a lot for doing so. Any alteration of the carb from the factory baseline, from a dealer or end-user perspective was illegal, not that it would necessarily stop me or anyone else. :taped:
Locust Cutter
Sawing for Sanity
I don't know why they made that model...
Was it a marketing idea that went afoul???
Not that they're bad, just sort of no home for them. Who would have been the targeted consumer group?
As I understood it was supposed to be the Husqvarna homeowner version of a MS650 Stihl...
Hedgerow
HACK
I believe the 570 replaced the 365 in the US when it came out. That did not last very long. The 575 replaced the 372 in the US at the same time.
Is this screwdriver the female torx style one to adjust the new splined adjustment screws on the 9010 for example? I ask because my local Dolmar dealer indicated that he was forbidden from Dolmar and the EPA from providing the adjustment screwdriver(s) and could in fact be fined a lot for doing so. Any alteration of the carb from the factory baseline, from a dealer or end-user perspective was illegal, not that it would necessarily stop me or anyone else. :taped:
It is more like a D shaped female torx style. Dolmar has part numbers for 2 different screwdrivers one for the Zama and one for the Walbro carbs. We are forbidden to sell them over the counter-and were told that a red flag would fly if we tried to order bunches of them..........
Locust Cutter
Sawing for Sanity
Gotcha. So when I buy it from Craftsman or Snap-on,.... Everyone wins?
zogger
Tree Freak
I was thinking similar, that nails it I guess. I would imagine it cuts just fine if it is a stratocharged 365, just numbered differently, if that is the only significant difference.
I don't about that-Just that I can't retail them without worrying about big brother looking over my shoulder!:censored:
Steve NW WI
Unwanted Riff Raff.
Just gimme 5 minutes with a caliper on one. We'll have options.
Might be an easier project for Mike on the mill though.
All because we live in a recently effed up tyranny state instead of the free country we were born into with the God given freedoms we were born with.
Mr. HE
Not hard to cut slots in the needle heads with a small high speed cutting disk. Also eBay has plenty of these drivers, and they're cheap.
All because we live in a recently effed up tyranny state instead of the free country we were born into with the God given freedoms we were born with.
Mr. HE
So god prefers that our so called freedom gives us the right to completely destroy our environment. OK then.
MRCo.
ArboristSite Operative
Popcorn time. opcorn:
opcorn:
