Any pointers for drilling (milling) holes in bars for modified alaskan mills?

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

gunnarfan

ArboristSite Guru
Joined
Nov 7, 2006
Messages
605
Reaction score
44
Location
Milford Maine
I've seen it mentioned that to get to your chain easier (for swapping out etc.) that its a good practice to do away with the alaskan clamps and put holes in your bar to bolt it direct to the alaskan. Any wisdom on this process (things to watch out for etc.)? Links to where this is discussed (or has been discussed) are always welcome.
 
I've seen it mentioned that to get to your chain easier (for swapping out etc.) that its a good practice to do away with the alaskan clamps and put holes in your bar to bolt it direct to the alaskan. Any wisdom on this process (things to watch out for etc.)? Links to where this is discussed (or has been discussed) are always welcome.
There's been several threads on the subject, but good luck finding them until the search function is fixed.

You'll need a carbide bit. I use a center cutting carbide end mill, but there are other types of carbide bits that will work, too. A standard steel drill bit will just make a mess attempting to drill through the nose bearing.

A steel bit may or may not work to drill the other end of the bar. Some bars, like Oregon and Windsor, are not particularly hard, while other bars, like Carlton, are darned hard.
 
Thanks for the heads up.

I was wondering why the searches weren't terribly fruitful. I've actually had to use google with the term and arboristsite in the search to get any real success (was looking up references to james mitchell's short log and timber building book...)

I have three bar sizes that I'm looking to work on. Will check the make on all.... i'm thinking all oregon.
 
Oil lots of it ,their made of work harden tool steel , so if hesitate at all its over . Drilling and bolting made a big difference in mill its sweet now three min chain change .
 
Carbide ball mills make short work of it. In a pinch I've made the pilot hole with a carbide ball bur in a dremel and then enlarged the hole with drill bits or a carbide bur.
 
i'll see if my table top vari speed delta can handle it. i might have a spare junk bar to practice on. might visit a buddy with a real machine shop if i have to.
 
I have also been trying to find info on drilling bars, I thought it was me not searching properly. One question, what size hole should you drill through the center of the sprocket bearing and are there any tips on not harming the bearing? thanks.
 
I did mine (30" Carlton) with a masonry bit using my Delta bench top drill press. That worked out pretty good. I did 1/4" holes for 1/4" bolts, may seem small but so far so good.
 
5/16" (1/2" head) so you can use a scrench to tighten them.

Here.... this will make drilling that bar very easy. Just a little cutting oil and a bit of pressure. Make sure to clamp the bar to the table because movement will shatter a carbide. It's also best to put a piece of scrap steel on the other side and drill into it such that the bit never breaks through the backside because that is when they often snag and break. Note the ball mill will want to walk less then a regular end mill.

Amazon.com: Niagara Cutter CB230 Carbide End Mill, General Purpose, Uncoated (Bright), 2 Flutes, Ball End, 13/16" Cutting Length, 5/16" Cutting Diameter: Industrial & Scientific
 
I used 3/8 fine thread bolts in the contruction of my home made version of an Alaskan mill. I run a 25 inch solid nose Oregon bar on a Stihl 090. I used the factory hole at the bar tip and drilled another one at the powerhead end. I used a drill press on the slowest speed I can get, LOTS of constant pressure and a standard 3/8 High Speed Steel bit. I Used bar and chain Oil as a cutting lube, and the bit chewed through the bar in about 10 seconds. I have also drilled Stihl bars this way and havent had a problem. As for drilling through the sprocket tip, i have never tried it, but at the risk of destroying a $68 tip, I think I will stick with solid nose bars for milling. I cut Tasmanian hardwoods, and the solid nose bars havent given me any trouble.
 
As for drilling through the sprocket tip, i have never tried it, but at the risk of destroying a $68 tip, I think I will stick with solid nose bars for milling.

Oregon and GB solid nose bars are like butter compared to the middle of sprocket nose bars. But I have drilled about a half dozen sprocket nose bars (2 x 25" , 30" and 60" Stihls, and 42" and 60" GB) and not damaged one. In fact I have never heard of anyone damaging a sprocket bar nose by drilling it.
 
Last edited:
I have destroyed a spocket nose by putting too much pressure on it and smashing the bearings. $15 from baileys.

I bought 3 extra tips and a friend with a water jet drilled all 3 in the center of the bearing. Now I can just add a tip to any sprocket nose bar and Have that end ready for the mill.

60 bucks for a tip????
 
I bought 3 extra tips and a friend with a water jet drilled all 3 in the center of the bearing. Now I can just add a tip to any sprocket nose bar and Have that end ready for the mill.

60 bucks for a tip????

Not everyone has a friend with a water jet. If I did, I would have plenty of stuff for him to do.

Probably $60 for a Stihl tip from the dealer.
 
This is coming from a guy that has screwed up a few times.

Get a carbide, center cutting end mill (or ball nose) Once you work harden a piece, even carbide will struggle to get through.

25 bucks for a good quality one, should last you a lifetime. (agree with the 5/16-18) Just go slow and careful on breakthrough, carbide will shatter like glass if abused.
 
As others have said, a carbide end mill works best. However, I have been able to get the job done with a sharpened carbide tipped hammer drill bit in a drill press. Low rpms and lots of oil and pressure.
 

Latest posts

Back
Top