Want to Sell Carlton .325 .050 and .058 rolls and other misc stuff

[fordf150]

1 roll of each.

K1L .325 .050 $225 shipped

K2L .325 .058 $215 shipped

paypal FF.

 

[fordf150]

chinese BB 7900 kit, used but only ran for a short bit. impulse nipple leaks where it is pressed into the cylinder. $35 shipped. SOLD

 

[fordf150]

New take off half wrap for 6400/7900. $45 each shipped

 

[fordf150]

oregon 88-025 mower blade sharpener. very low use, doesnt even have the paint worn off where the blade slides past the wheel. $200 and I'll split shipping cost.

 

[fordf150]

Used saws. shipped free on the east coast. paypal FF or add 3%

Husqvarna 142 $75

Stihl 029 $200


NEW w/warranty Dolmar PS-510 saw was left on a shelf in the shop for a couple years so somewhat dirty, wiped it off and left some scratches in the top cover $300

 

[kz1000]

do you still have the .325 chain?

 

[kz1000]

Where in Ohio?

 

[fordf150]

do you still have the .325 chain?

Where in Ohio?

still here

southeastern....newcomerstown. its exit 65 on I77

 

[kz1000]

Now I see where your at, you said south ohio but your north of me. I'm in Glouster area. On the chains, I'm not that familiar with k1l is it low kick or regular? semi or full? Thanks

 

[fordf150]

Now I see where your at, you said south ohio but your north of me. I'm in Glouster area. On the chains, I'm not that familiar with k1l is it low kick or regular? semi or full? Thanks

to most of the state we are southeastern ohio but i guess not to you since you're in BFE

k1l is like 20lpx without the bumper drive links

 

[kz1000]

Let me see which I have the most bars in, 50 or 58 and get back. Might do a road trip?

 

[Alex Perez]

Good morning wanted to know if the Dolmar PS-510 it's still available?

Used saws. shipped free on the east coast. paypal FF or add 3%

Echo CS400 18" with case. new chain on it and original but dull one included as well. only has a tank or 2 thru it. $200

Husqvarna 55. nice clean saw with a new OEM recoil and wrap handle on it. very low hours. $225

Husqvarna 142 $75

Stihl 029 $200

Dolmar PS-510 new saw but was left on a shelf in the shop for a couple years so somewhat dirty, wiped it off and left some scratches in the top cover $300


View attachment 622125 View attachment 622126 View attachment 622127 View attachment 622128 View attachment 622129 View attachment 622130 View attachment 622131 View attachment 622132

Used saws. shipped free on the east coast. paypal FF or add 3%

Echo CS400 18" with case. new chain on it and original but dull one included as well. only has a tank or 2 thru it. $200

Husqvarna 55. nice clean saw with a new OEM recoil and wrap handle on it. very low hours. $225

Husqvarna 142 $75

Stihl 029 $200

Dolmar PS-510 new saw but was left on a shelf in the shop for a couple years so somewhat dirty, wiped it off and left some scratches in the top cover $300


View attachment 622125 View attachment 622126 View attachment 622127 View attachment 622128 View attachment 622129 View attachment 622130 View attachment 622131 View attachment 622132

 

[fordf150]

Dolmar 7900 red top. gone thru top to bottom, new PTO case half, both bearings, seals, piston ring, updated oil lines, fuel line, fuel filter, carb kit, upper A/V mount, added the limiter, almost new RSN bar with a used chain, air filter, impulse line, and plug


Makita 6401. gone thru top to bottom, new 7900 P&C, updated oil lines, clutch drum, oil pump rebuilt, upper A/V spring, added the A/V travel limiter, new Carb, impulse line, fuel filter, and plug

$525 plus shipping paypal FF.


@Dahmer

 

[kz1000]

Nice shop, I'll try to get there some day.

 

[kz1000]

The money for the .050 is sent with a note for the address.

 

[Johnmn]

F me that red top is sexy and calling my name!

 

[fordf150]

F me that red top is sexy and calling my name!

I fell in the same trap.....just couldnt let a nice red top get parted out when the only big piece it needed was a case half, didnt figure in all the small pieces parts it would need to bring it up to date. Had a chance to sell it last nite to a logger and i couldnt bring myself to do that either....hated the idea of a logger using it daily and possibly destroying it so i just made him a good deal on a new saw

 

[Deleted member 149229]

Dolmar 7900 red top. gone thru top to bottom, new PTO case half, both bearings, seals, piston ring, updated oil lines, fuel line, fuel filter, carb kit, upper A/V mount, added the limiter, almost new RSN bar with a used chain, air filter, impulse line, and plug


Makita 6401. gone thru top to bottom, new 7900 P&C, updated oil lines, clutch drum, oil pump rebuilt, upper A/V spring, added the A/V travel limiter, new Carb, impulse line, fuel filter, and plug

$525 plus shipping paypal FF.


@Dahmer

View attachment 626196 View attachment 626197 View attachment 626198 View attachment 626199

If I can move either the 2166 or 5105 I’ll be calling back and driving over for that blue 7910.

 

[RedneckChainsawRepair]

I fell in the same trap.....just couldnt let a nice red top get parted out when the only big piece it needed was a case half, didnt figure in all the small pieces parts it would need to bring it up to date. Had a chance to sell it last nite to a logger and i couldnt bring myself to do that either....hated the idea of a logger using it daily and possibly destroying it so i just made him a good deal on a new saw

Just went through that on a very nice saw that should be on a shelf in a collectors hands too. Logger wanted a 60cc BB for a limbing saw.

I got the saw to get in the right hands. Not to be worn out and ruined in a year.

 

[Deleted member 149229]

Dolmar 7900 red top. gone thru top to bottom, new PTO case half, both bearings, seals, piston ring, updated oil lines, fuel line, fuel filter, carb kit, upper A/V mount, added the limiter, almost new RSN bar with a used chain, air filter, impulse line, and plug


Makita 6401. gone thru top to bottom, new 7900 P&C, updated oil lines, clutch drum, oil pump rebuilt, upper A/V spring, added the A/V travel limiter, new Carb, impulse line, fuel filter, and plug

$525 plus shipping paypal FF.


@Dahmer

View attachment 626196 View attachment 626197 View attachment 626198 View attachment 626199

Hey Nate, sold the Mary. Sent you pm and I’ll call the shop, I’ll take the 6401/7900.