Saws that surprised you...

[Mastermind]

It's the blue goo.

 

[bryanr2]

did it have a pop up?

Tigerloff (was the scandal) Randy was the builder. He built him that saw. Tgerloff got it back and then went in it and a 5100 Randy did as well. DexterDay wound up with the saws, he sold them, both saws wound back up in Dex's possession and back in Randy's shop and became the infamous "Tgerloff blue goo" saws. Randy redid the 395, and Dex was trying to trade for a 441cm on here, I asked him what he could buy a 441cm for, and paid him that for the 395xp. I dont know if having Randy in the saw twice contributes to how strong the saw is.... but it couldnt have hurt anything. The saw is rediculous.

 

[gary courtney]

Really? I read where Wiggs had an interest in the 600p, but there wasnt much explanation to his interest.

randy ported mine and I carried it to the echo dealer and ran against a stock 600 and a 680 stock and their mouths dropped. that 60 cc is bad to the bone

 

[MS460WOODCHUCK]

Alot of saws have impressed me but the most recent would be my type 3 60cc poulan 3450. In stock form with just a mm it will run with any stock 60cc saw.

 

[Ronaldo]

Echo 600p. Good AV, filtration, and performance. Before it was broke in, it would cut faster than my muff modded husky 359.

 

[buzz sawyer]

Most recent was the Homelite 500 I saved from the scrapyard. Had to change the P&C and carb diaphragms, otherwise just a clean up and sharpen the chain.
Here it is running .404 chain through some white oak.

 

[M&Rtree]

For me its my 372. The first 372 I had was OK but this one is a freak. Compression is only 160 that I've read but with a 24 b/c its fast. Its out cut all my 70cc saws, at a buddy's small gtg it out cut his 441cm modded, a 7300 Dolmar, another 372,460 mag. My other 372 is 2 seconds slower in the same log and it has a new ring. Second would be my clean 262. It stays even with my 562 it blows 165.

 

[jughead500]

Sawtroll 3....2....1

What there are 600p threads going on without me? Yeap they are impressive.everybody likes mine when i start it and it starts to crackle.i always run a 20" 70dl but for the hell of it i bought one of those 16" GB bars from left coast and put on a 33rc chain.was going to put on a 8 pin rim sprocket but i've misplaced it.it suprised me when i took off the clip and washer.i was expecting a small spline sprocket.
Yeap the 600p is awesome.don't know if its ms362 awesome but its definitely awesome.

 

[Ferguson system]

For me its my 372. The first 372 I had was OK but this one is a freak. Compression is only 160 that I've read but with a 24 b/c its fast. Its out cut all my 70cc saws, at a buddy's small gtg it out cut his 441cm modded, a 7300 Dolmar, another 372,460 mag. My other 372 is 2 seconds slower in the same log and it has a new ring. Second would be my clean 262. It stays even with my 562 it blows 165.

Does it have anything to do with your new 372 being a x-torq or is it the old version?

 

[M&Rtree]

Both are the old version.

 

[M&Rtree]

What's better the 600p or 620p?

 

[jughead500]

What's better the 600p or 620p?

Don't know havent ran the 620.i'm sure the 620 is probably stronger though.i've been debating on buying what parts i need to convert the 600 over to a 620 but im sure a whole running 620 would be cheaper than just a coil,piston,cylinder and carb.

 

[M&Rtree]

I'm thinking the same difference as a 555 vs 562. Power wise.

 

[strtspdlx]

335xpt muffler mod and super shady bottom end work. I
Bought it off eBay and started tinkering with it. Replace crank bearings and while I was in it polished belly pan and lightly touched the ports to clean up. For what it is I can sunk the bar clean in oak ad it never misses a beat


Sent from my iPhone using Tapatalk

 

[jughead500]

I'm thinking the same difference as a 555 vs 562. Power wise.

I'm patiently waiting for mastermind meets the cs620p. If i had the money i'd buy one and hand deliver it to him to play with.

 

[295 tramp]

I rescued a Jonsered 535 from the scrapyard, it was a complete saw pulls over like it has 170psi, gave it a carb rebuild.
I couldn't believe how snappy it was. it has become my front line limbing saw.

 

[M&Rtree]

I'm patiently waiting for mastermind meets the cs620p. If i had the money i'd buy one and hand deliver it to him to play with.

Did some digging 620sx is rated at 3.32kw in power.

 

[mesupra]

Having run a Husky 345, Jonsered 2050 and Stihl 026 I was very impressed when I first tried a 346xp. Even stock they are great saws.

 

[Duke Thieroff]

Definitely a 200t. There's a lot of grunt in a small package there.

2100 Husqvarna.

372 is the only saw I've seen that lived up to the hype.

346s and 262s are ok.

 

[DeckSetter]

The one with the sharp chain.