Back In The Shop......Now What's On Your Bench????
- Thread starter Mastermind
- Start date
Help Support Arborist Forum:
Brianlol
Do u see, chainsaws are not just for trees lol
- Joined
- Nov 26, 2014
- Messages
- 435
- Reaction score
- 272
Alright!!!!
First update Lolol
My OEM Rustoem paint does not hold up. First time out and have chips in paint job
Let have some suggestions on paint please. I went though a lot of time to make it look nice. I hope u guys have a better solution.
First update Lolol
My OEM Rustoem paint does not hold up. First time out and have chips in paint job
Let have some suggestions on paint please. I went though a lot of time to make it look nice. I hope u guys have a better solution.
Mastermind
Work Saw Specialist
One word.
Powder Coating from Mike AKA Glock37.
Ok........that's more than one word.
Powder Coating from Mike AKA Glock37.
Ok........that's more than one word.
028s for seals ans slight timming advance, got it cheap
5 loonies,but someone must have been cutting shellac
with it 2 hours to clean it , not a you suck deal I can tell ya
5 loonies,but someone must have been cutting shellac
with it 2 hours to clean it , not a you suck deal I can tell ya
Mastermind
Work Saw Specialist
Brianlol
Do u see, chainsaws are not just for trees lol
- Joined
- Nov 26, 2014
- Messages
- 435
- Reaction score
- 272
Have an old toaster oven that would fit two halves perfectly. Ur right time to try. I had it looking so good and after one day of cutting for an hour left to many scratches and chips. So disappointingFind an old oven........and it's on.
Not on my bench but on a card table in my garage presently, a Stihl 029 torn completely apart and cleaned, was awaiting a new p/c and seals. Some items aren't here yet but I did get the seals today and put them on the crank and set them in the crank cap. I ordered the correct sealant for the bottom end but it's not here yet, should be here tomorrow or Saturday then I'll get started with the assembly.
Deets066
Firewood hack
Hurry ta hell up and get a bar on that thing. You drop it on your foot like that and it's gonna hurt
Nitroman
Addicted to ArboristSite
I'll be able to take a nice picture of my 24'x36' SHOP once the wife and I close on a property. Got the appraisal, sent it to insurance company for quote. So now we are just waiting. Closing on June 1. The shop already has air plumbed in on a big compressor, but I'll change that 'cause it's black iron pipe. I don't want any rust going into my turbine grinder. Lots of space. Oh, it has windows too. And a heater. And insulation. Maybe I should get a bridge crane? Maybe 4,000 pounds? Next year.....
I can't WAIT and it's a DRAG! So.....that's what's on my bench.
I can't WAIT and it's a DRAG! So.....that's what's on my bench.
KG441c
Keith
This 440 was painted with Valspar Tractor and Implement Paint in a rattle can in husky orange and AC colors. Ive did several saws with this paint and if u let air dry about three days its hard as a rock!! Did this 262 in valspar husky alsoAlright!!!!
First update Lolol
My OEM Rustoem paint does not hold up. First time out and have chips in paint job
Let have some suggestions on paint please. I went though a lot of time to make it look nice. I hope u guys have a better solution.
Mastermind
Work Saw Specialist
That sounds great Roger !!!!!!!
old-cat
Fir Man
My bench is getting buried in saws and I can't do squat! It's been two weeks now since that 181se saw attacked my leg and its still got a big knot. Doc says I have to stay prone for it to heal.
Good luck with your recovery.
Mastermind
Work Saw Specialist
OK.....what did I miss Lynn?
Sounds like a very nice setup fella. Hopefully you will get lucky and the prior owner had a dryer before the tank. You may possibly be able to keep the iron.
Stihlofadeal64
Addicted to ArboristSite
The Valspar Tractor paint -- isn't that the brand they sell at Lowe's? You mentioned you bought it in "husky orange and AC colors" --excuse me, I'm on the short bus today. What are "AC colors"
Saws look good from here. I'm interested in the durability and how the finish lasts on the plastics. Not saying it won't just interested in knowing. Thanks for posting.
old-cat
Fir Man
My post from Fear of pavement's thread "What did you do today"
This stinking 181XP Husky put a knot on my lower leg the size of a hardball! Tried to drop start it without b/c on, fresh rebuild, gas squirt into carb. All I could get was about 3 revolutions, SLOW. NO starty! Then wham! A bare bar stud hit my leg.
Husky Critters
Today it finally felt a little better!
