Back In The Shop......Now What's On Your Bench????

[spencerpaving]

View attachment 413524

After a rough run at Fryeburg, I tore 5 buffers, gas tank plate,messed the bar nose up, ripped the front leg off and toasted the chain. That was not so fun.

looks slow....is that a briggs and Stratton?

 

[stihlman036]

looks slow....is that a briggs and Stratton?

K125 Comer minus the shrouds...

 

[bikemike]

looks slow....is that a briggs and Stratton?

Lmao

 

[bikemike]

Id love to have the funds to build a wankle powered saw sometime. Seen a youtube vid of a foreign guy test running a wankle in a procart and as a single speed set up it was waxing the shift carts. And they perform on a simple exhaust system. They dont sound as cool as that race saw

 

[Jeepsnchainsaws]

Id love to have the funds to build a wankle powered saw sometime. Seen a youtube vid of a foreign guy test running a wankle in a procart and as a single speed set up it was waxing the shift carts. And they perform on a simple exhaust system. They dont sound as cool as that race saw

Wankle saw would be NASTY!

 

[Jeepsnchainsaws]

Port and polish, fiiiinally finished it this morning, wife stepped out for a bit .

 

[stihlman036]

The wankle I ran against didn't make as much power as most of the rotax motors.... but it was brutally loud

 

[Jeepsnchainsaws]

I don't know? What size engine is a wankle considered?

 

[stihlman036]

Check YouTube, they have a carbon fiber pedestal they sit on.....

Side note, with the changes to Boonville's hotsaw rules, I don't think they meet the 5" rule.

 

[295 tramp]

Finally finished up the 084 yesterday. I took it down to the log pile today. I'm still tuning it in, I have the idle screw all the way in and
I can't get it to idle up any more, any thoughts or suggestions?

 

[bikemike]

Wankle saw would be NASTY!

Yeah man never once seen or heard of a person run one but artic cat use to have one in a sled years ago. And on grass iy would stand up on end from dead stop

 

[bikemike]

I don't know? What size engine is a wankle considered?

Depends on the engine the rx 7 mazda had a way smaller displacement then datzun 280 z 6 cylinder. Wankles didnt have the torque but they had lots of power and you cant throw a rod or float a valve

 

[bikemike]

Aixro xr 50 50 hp about the size of a 5.5 honda

 

[splitpost]

Finally finished up the 084 yesterday. I took it down to the log pile today. I'm still tuning it in, I have the idle screw all the way in and
I can't get it to idle up any more, any thoughts or suggestions?View attachment 413728
View attachment 413729
View attachment 413730
View attachment 413731

whats going on with the melted handle and hood

 

[bikemike]

whats going on with the melted handle and hood

Maybe its so fast the plastic couldn't keep up

 

[bikemike]

Is 294cc single to big for race saw rules?

 

[bikemike]

View attachment 413659 Port and polish, fiiiinally finished it this morning, wife stepped out for a bit .

whats the inside jug look like

 

[bikemike]

View attachment 413659 Port and polish, fiiiinally finished it this morning, wife stepped out for a bit .

whats the inside jug look like

 

[bikemike]

Finally finished up the 084 yesterday. I took it down to the log pile today. I'm still tuning it in, I have the idle screw all the way in and
I can't get it to idle up any more, any thoughts or suggestions?View attachment 413728
View attachment 413729
View attachment 413730
View attachment 413731

You just made Italians jealous of ur pasta processor

 

[stihlman036]

Just send up for stumping or milling