MS460 group
- Thread starter mattmc2003
- Start date
Help Support Arborist Forum:
windthrown
361 Junkie
I just got the DP cover and put it on this afternoon. The 044 ran like a raped ape before, now it screams even faster and louder than a raped ape. Not as loud as I expected it to be though.
460 Part numbers (including the nuts and bolts that you need for the outer spike):
DP muffler cover: 1128 140 0801
These are for the 460 (the 440 has a different outside dawg number):
Inner (skinny) big spike: 1122 664 0506
Outer (fatter) big spike: 1128 664 0501
Roller chain catcher (w/nuts and bushing): 1122 650 7700
Bolts: (2) 9008 319 0960
Nuts: (2) 9214 320 0700
The nuts and bolts are for the outer spike that go into the side cover. You use the bolts off the original inner spike for the larger inner spike.
I ran an 8 pin on my 460 running a 20 inch bar and it was fine. An 8 pin rim may bog on you with a 25 inch bar. I would try it. I found that my 044 bogged down some buried deep in fur with full comp 25 inch, but that was before I put on the DP muffler cover. I will have to try the 25 inch bar with an 8 pin rim tomorrow.
460 Part numbers (including the nuts and bolts that you need for the outer spike):
DP muffler cover: 1128 140 0801
These are for the 460 (the 440 has a different outside dawg number):
Inner (skinny) big spike: 1122 664 0506
Outer (fatter) big spike: 1128 664 0501
Roller chain catcher (w/nuts and bushing): 1122 650 7700
Bolts: (2) 9008 319 0960
Nuts: (2) 9214 320 0700
The nuts and bolts are for the outer spike that go into the side cover. You use the bolts off the original inner spike for the larger inner spike.
I ran an 8 pin on my 460 running a 20 inch bar and it was fine. An 8 pin rim may bog on you with a 25 inch bar. I would try it. I found that my 044 bogged down some buried deep in fur with full comp 25 inch, but that was before I put on the DP muffler cover. I will have to try the 25 inch bar with an 8 pin rim tomorrow.
Last edited:
help!!!!
i ran across a spike for my saw that a freind had and i need the inner that matches.the part number is 1122 664 0503 on my outer spike..can you guys tell me which number will match up with the other spike .thanks
i ran across a spike for my saw that a freind had and i need the inner that matches.the part number is 1122 664 0503 on my outer spike..can you guys tell me which number will match up with the other spike .thanks
Last edited:
brownie525
ArboristSite Member
okay i have a question now. i just ordered a set of dogs for my 460 today i just looked at the invoce and the part number is 1128 664 0500 for the inside and 1128-664-0501 for the out side how come the inside one is a different number then what everyone is posting? will it fit my saw
NC4TN
ArboristSite Operative
I like this thread! Now I'm getting ready to saw a little boundary of dead standing locust for firewood, and I'm gonna' buy a 460 just for the task. (Got to have more power for a quick cut, 'cause the stuff rains dead limbs and I need to get out of the way fast) Anybody had any bad mechanical experiences with their late model MS460's?
Stihl 038 Super (Made in WEST Germany, by jingo!)
Stihl MS290FB
Stihl MS260Pro
Husky 55
Sears H47D (1964-vintage)
Ford 3930 FWD tractor
Timberwolf TW5
Nell and Queen (Two Percheron mares, retired; goes where the skidders won't even look!)
Stihl 038 Super (Made in WEST Germany, by jingo!)
Stihl MS290FB
Stihl MS260Pro
Husky 55
Sears H47D (1964-vintage)
Ford 3930 FWD tractor
Timberwolf TW5
Nell and Queen (Two Percheron mares, retired; goes where the skidders won't even look!)
wvlogger
Rock trucker
i own a 460 and i feaking LOVE IT!!!!!!!! it is muffler modded and soon to be ported. im in
windthrown
361 Junkie
okay i have a question now. i just ordered a set of dogs for my 460 today i just looked at the invoce and the part number is 1128 664 0500 for the inside and 1128-664-0501 for the out side how come the inside one is a different number then what everyone is posting? will it fit my saw
Uh oh... looks like they screwed up and ordered the smaller single dog as the inside one. You want the larger skinny inside dog. My IPL for the 460 shows the smaller inside dog as 1128 664 0500 and the larger inside dog as 1122 664 0506. The larger one is the one that matches 1128-664-0501 on the 460 (as listed on my post above) and the one you need to set the roller between. Someone does not know how to read the screen right at your Stihl dealer. The small dog will fit your saw, but it will not match the larger outside dog that you ordered.
See, these are a pair of large outside dogs here:
Oops, sorry, these are the type of large falling dogs that you want with the roller:
Last edited:
brownie525
ArboristSite Member
oaky thanks for the help ill have to get on the horn tomorrow morning and get it straightened out. The guy at the dealer wasnt a bad guy, he didnt really know what he was doing but wasnt a a bad guy. I knew there was going to be a problem when he handed me two outside dogs when i asked him for a set he was foubleing around on the computer for almost twenty minutes trying to figure it out and it looks like he still didnt get it right
Anyone have the parts list for the 460 then can send me?
he was foubleing around on the computer for almost twenty minutes trying to figure it out and it looks like he still didnt get it rightAnyone have the parts list for the 460 then can send me?
muffler
i want to mod my muffler but am nervous about doing it dont want to shorten the life of my saw or does it help it out more
i own a 460 and i feaking LOVE IT!!!!!!!! it is muffler modded and soon to be ported. im in
i want to mod my muffler but am nervous about doing it dont want to shorten the life of my saw or does it help it out more
Nuzzy
Trail Gnome
Alright, I'll play with pics (even though this is a MS460 group and I only have a lowly 046)...
windthrown
361 Junkie
Shorten the life of the saw? By running it cooler with better flow, with a dual port factory muffler designed for the saw by Stihl??? :monkey:
In all likelyhood you will increase the life of the saw with the muffler mod, as long as you richen up the carb (easy turn of the H screw) after you add the dual port muffler. For a mere $32 and change.
Last edited:
I even triple port some of my saws no problems so far.
windthrown
361 Junkie
You mean the orange thing that goes over the nose of the bar?
Or the side cover that the chips fly out of?
The large side cover is the same on the 440/460/660 are the same. This information is from 2000ssm6's sig line:
440/460, 044/046 Dual port muffler cover # 1128 140 0801
660/066 Dual port muffler cover # 1122 140 0800
Large felling dawgs
440/460 inner: 1122 664 0506
440 outer: 1122 664 0501
460 outer: 1128 664 0501
660 inner: 1122 664 0508
660 outer: 1122 664 0503
Chain catcher/roller (fits all 3): 1122 650 7700
PNW clutch/side cover(fits all 3): 1122 648 0401
Last edited:
modding my muffler????
okay can you guys tell me what will work best..i want to do the dp cover.do i need to do anything else with it like making the stock hole bigger???if so tell me how big to make the hole....thanks
okay can you guys tell me what will work best..i want to do the dp cover.do i need to do anything else with it like making the stock hole bigger???if so tell me how big to make the hole....thanks
2000ssm6
Stihl User
Nope, if you need more flow open the DP cover. Here is an example but I didn't try to put the screen back in. For a stock 460, just adding the DP cover is fine.
Don't forget to richen carb!
Last edited:
Nope, if you need more flow open the DP cover. Here is an example but I didn't try to put the screen back in. For a stock 460, just adding the DP cover is fine.
Don't forget to richen carb!
thanks i cant wait to get it done..
diesel&coffee
ArboristSite Guru
I have a 361 that thinks it's a 460 :yoyo:
