Swap meet...

[epicklein22]

I got a cylinder for my S25CVA. I need a piston/rings now, as well as the AV mounts.

Would one of these craftsman's work?
Craftsman Chainsaws, 3 total

 

[stihl_collector]

I need a muffler or front muffler cover for a dolmar 153.

 

[blsnelling]

Would one of these craftsman's work?
Craftsman Chainsaws, 3 total

I would have to be the larger 38cc piston.

 

[HittinSteel]

Needing everything between the carb and jug for a 281/288

 

[sefh3]

I got a cylinder for my S25CVA. I need a piston/rings now, as well as the AV mounts.

Brad,
Do you know what the Craftsman model would be? I have a 358.357230. Would that work for you?

 

[blsnelling]

Brad,
Do you know what the Craftsman model would be? I have a 358.357230. Would that work for you?

I have no idea at all. Maybe Mark would know.

 

[jockeydeuce]

Needing everything between the carb and jug for a 281/288

Gotcha covered Bryan......PM me your address again.

 

[paladin]

Looking for a good Stihl 036 crank one off of 034 or ms 360 is the same.
I have some husky 340,345,350 parts no mufflers,pistons,cylinders,cases or clutch covers but everything else. Also Mac 10-10,700 and 610 parts depending on what you need. Also some Homey Ez (I think) parts saws.

 

[PB]

I have the following parts for trade:

Jonsered 2145/Husky 345 cylinder- no scoring that I can see but came off of a saw with low compression (bad bearing destroyed the piston).
Jonsered 630/Husky 162 cylinder - minor scoring, posted pictures here before and was told to run it as is.

PM me if you are interested. I can get pictures if you are interested.

 

[TRI955]

I need a carb for a 288xp

 

[bigblockburris]

Poulan 2450 AV Spring needed

This is for Lil' Possum. His internet is down.

He needs a AV spring for a Poulan 2450.
Anbody got one?

Thanks!
BBB

 

[Mastermind]

This is for Lil' Possum. His internet is down.

He needs a AV spring for a Poulan 2450.
Anbody got one?

Thanks!
BBB

I'll check, think there's a carcass in the shop.

 

[little possum]

This is for Lil' Possum. His internet is down.

He needs a AV spring for a Poulan 2450.
Anbody got one?

Thanks!
BBB

Need the spring from the cylinder to the handle. Also could use a smaller bar

 

[wigglesworth]

Still lookin for 046/460 jugs. Lots to trade or some $$.

PM me whatcha got.

 

[caleath]

I am looking for a brake handle for ms 210 could use the sprocket cover too. Let me know whatcha got.

 

[epicklein22]

I am looking for a brake handle for ms 210 could use the sprocket cover too. Let me know whatcha got.

Believe I have both, but will have to double check when I get time to head over to my storage spot.....

 

[tntnt44]

homelite sxl 925

Hi I need the the trigger handle air box combo and a 24 inch or so bar and chain can trade or dollars thanks:msp_wink:

 

[MS460WOODCHUCK]

still looking for 2149 top cover

 

[F-545]

066 parts

I have 2 o66 rebuilders ,would like to trade for a good 044 or 440
pm me for more info:msp_biggrin:

 

[7hpjim]

I need a carb for a 288xp

I have one off a 281xp that's been cleaned & freshly rebuilt by a local Amish shop.