Trx250r180
Saw polisher
With over 200 psi comp ,ive had a couple stihl comp releases fail,so far the husky has held up,they start spiting black goo on the plastic when the valves get weak
What's on your bench? 05-12-2013
- Thread starter blsnelling
- Start date
Help Support Arborist Forum:
With over 200 psi comp ,ive had a couple stihl comp releases fail,so far the husky has held up,they start spiting black goo on the plastic when the valves get weak
I've had better luck with the Husky release valves my own self. Even the aftermarket releases seem to last longer than the Stihl OEM ones.
FergusonTO35
ArboristSite Operative
On my bench right now: the new/used Echo CS400 getting a cleaning and final tune, Dad's Poulan 1950 getting a new top cover and probably a carb kit, Echo CS300 basket case that I got cheap on Fleabay, and a Poulan weedeater getting a carb kit. Beside the bench are two push mowers being fixed for other people. Hanging on the wall behind the bench on display are a Homelite Super 2 and ST-80 weedeater.
I've got a couple of 101B's getting put together for the GTG. Well at least one will make it. I have a nice clean 125 with a scored piston that's getting a kart engine. The usual custom fitting a parts reminds me of my racing days. Had to drill the hole for the manual rod to actuate the pump. Had to trim the intake manifole as well. Will have to fit up a rear mount. The other 101 was a saw but needs a lot of work. I have all the parts to get them running, just not the time.
181 husky clutch dragging, posted y'day w/pic of spring... looks tired, re: gap beween hooks, was lookin 4 help/opinions here... TIA.
At the moment nothing waiting for my 660r that brads got!!!! I didn't order the 261 but won't complain if you send it my way brad! I am excited as hell and that's only looking at the box! (Guess I always get excited looking at box)
old 040
Addicted to ArboristSite
it did look to me that you need a new spring...............
......................BTW, here's what's on my bench at the moment, just gettin familiar with it..............View attachment 295174
Last edited:
Steve NW WI
Unwanted Riff Raff.
Greasy tractor parts waiting their turn in the parts washer.
Saw stuff is on hiatus for a bit.
Saw stuff is on hiatus for a bit.
Got this old Poulan waiting its chance to get into some wood. Actually finished it up several weeks ago, and started it, just havn't had the wood to try it in yet. And busy with other stuff.
Gregg,
Gregg,
Excellent work Gregg!!!
sarge3604
Maine-iac
Stihl fs 36 trimer needs to be tuned 034 and husky 268 need sharpening pretty bad.
chadihman
Addicted to ArboristSite
Just send it to me I'll break it in at 9000 rpm loaded on a tank of gas then test hp on the dyno
Trx250r180
Saw polisher
i have an orange and white can looks like one of these ,says stihl on it ,gas can lifts off and storage for chains files etc on lower half ,are these like that ?
The 261 is done and headed out tomorrow morning. The 660R is next on the bench. It's getting the squish band cut and porting.
I bought these two nice Blitz cans for $25. They have minor surface rust on the inside, so I've got them filled with vinegar(acetic acid).
Gravedigger
ArboristSite Operative
Startig First rebuild Stihl 024. Waiting on parts that I just ordered.
JakeG
Addicted to ArboristSite
Bunch of small stuff on the bench at the moment...
Poulan 2000 & 2300 (Been sitting for ten years or more)
Lastly... Finishing my buddy's MS290 (General Maint). In its 4 years, the chain was never sharpened, bar never flipped, filter never cleaned and covers mever removed for cleaning. :msp_thumbdn:
Poulan 2000 & 2300 (Been sitting for ten years or more)
Lastly... Finishing my buddy's MS290 (General Maint). In its 4 years, the chain was never sharpened, bar never flipped, filter never cleaned and covers mever removed for cleaning. :msp_thumbdn:
old-cat
Fir Man
My bench work is like watching a slug in high gear! I don't even keep them on the bench unless I think something is getting close to happening. I have my MS361 on the bench right now cause Terry L. said my ported cyl. is coming back, ready to go! My MS260 is waiting for an 026 to appear for parts swapping. My MS440 is so far down the line I can't even begin to think about it. As soon as the 361 hot rod is going, my 034 Super will get squished (.020")
Plan and simple I don't have time to rebuild saws now it's racing season; two to three nights a week working on the car then all weekend racing it :cool2:
I spent over 12 hours on the road this past weekend in two different states chasing the dream and spending way to much money do that
I spent over 12 hours on the road this past weekend in two different states chasing the dream and spending way to much money do that
Actually, this is trx250r180's hybrid. It's here with Randy's permission. I just thought I'd have some fun and see how long it took for you guys to notice. I'll have to say, you were a little slow!
I noticed right off. Just wasnt going to say anything to ruin your fishing trip Brad
. :msp_tongue:Poulan 445 70.7cc quad port on the bench.
