Search results

I took these off a MS441 that I converted to a mtronic one. I couldn't locate a mtronic flywheel with heater magnets. Was working when removed. I'm no longer building saws and this is the last parts that I have. What you see is what you get. Standard carb crankcase flywheel half. Standard...

Im making a 562xp display from a bunch of junk parts. I've cut it in half and am still looking for a few more parts. I'm needing the heat shield, muffler, black air baffle, intake bellows, carb and filter manifold/filter. Basically all the stuff in this ipl pic. I'm really looking for free...

I'd like to buy a kombi powerhead side driveshaft. Specifically 2,3 and 6 in the pictured ipl.

I've got an extra 562xpw that I want to sell. This saw has a new oem crankcase assembly and a new p&c. The cylinder has a few bad decomposition threads. It appears to be a casting void. I plugged the hole with an oem plug and it passes pressure and vacuum tests. I replaced the worm, the oil...

I'm looking for a bad 562xp piston. I know it sounds weird, but I have a bad tank, crank/case and cylinder. I want to cut them in half to make a display, and didn't want to buy a new one. I could also use a crushed/bad muffler too.

I'm looking for a 562xp clutch.

I'm looking for some 562xp parts. I've got a enough parts to assemble a parts saw, but need some items. Parts I need: flywheel, av springs, recoil side air guide plate, chain guide plastic piece above oil pump, chain brake spring and handle/av mounting screws.

Looking to buy an oem half wrap 562xp handle.

I'm looking for a 550xp project saw.

I picked up a 562xp with a piston pin bearing failure that destroyed the jug. I'm replacing both crank bearings, both seals, new oem P&C. I'm planning on giving it a mild port job and copy some numbers from a big builder. I plan on removing the base gasket and adjusting squish with a...

I'm rebuilding a 346xp and was pressure testing it. It had about 1/2 psi leak over about 5 minutes. I got soap water and a brush and put it around all the common leak points and didn't find anything. Put it around the crankcase gasket and found it. So, I dirkoed the gasket around the...

I picked up a really clean ms250 with questionable bearings. I figured I'd widen the ports. I decided to see what the numbers were. Bore: 42.5mm 65% bore = 27.6mm Intake: 80° stock port width: 19.9mm Exhaust: 98° stock port width : 21.5mm Transfers: 129° Squish: .039" I double checked...

I'm working on porting my 346xp and have the following numbers: Intake: 74 Exhaust: 104 Transfers: 124 I have done ignition advances on my Stihls and 372xp. I cannot find any info through searches. Does the NE 346xp like an ignition advance?

I'm looking for a husky 455 or 460 clutch cover. It's the one with 2 holes and adjuster. Looks like this:

I bought the 346 from ebay thinking it was a ne because it had the primer , top cover said 50cc and gray clutch cover. After getting it and breaking it down for rebuild I discovered a few things off. The primer bulb (ne) wasnt hooked to anything. The carb didn't have a return line for it...

I'm looking for 346xp crankcase halves. I think 351/353 cases will work also.

I got this cylinder in a bunch of parts. Its a 024. Does the 'S' stamp on the top indicate this was a 024 super?

I have a old 028 with metal tank that was given to me. I got around to tearing into it and discovered an pointless ignition coil and a newer flywheel. After pulling the jug, I discovered it was 44mm, the serial number is 87xxxxx. Is this the original cylinder? There are no Stihl markings...

I'm looking for an outer (clutch cover) small oem dog for a 372xp.

I converted my MS441 arctic to mtronic from a donor saw. I'm looking for the Mtronic flywheel with the inside magnets for the handle heaters.