Search results

ms211 service and IPL Anybody have these?

If I go with the Big Bore kit do I have to do anything special or is it just a bolt on replacement?

I picked up a 046 that needs a piston and probably cylinder. I only have $60 into the saw, so spending a little cash to get a piston and cylinder kit is what I want. The saw will get a dual port muffler but the rest will be stock. Is the 54mm Big Bore kit, better than the standard kit if I...

046 service manual Anybody want to share this.

Thanks for the info, exactly what I needed to know. Can anybody verify this stihl part number 1128-021-0761 could be a 460 or 044/440 case part number.

I need a clutch side case half for a 046, will a 044 case work? The item I am looking at says 044/064 case but I dont see how they can be the same. The stihl part number that I could make out is 1128-021-0761 which is the flywheel side but it comes with both halves.

Stihl 046 Anybody have a 046 IPL?

My buddy has a well used 046 that wants to trade me for my brand new stock 260pro. I already have a ported 260 that I use instead of the stock 260 and a 361. The 046 seems to run good but is this a good deal? My 260...

I run a ported 260 and a 361, use the 260 as the go to saw on almost everything. I like the 361 but its to close in size to the 260. I would rather have a 440/441 which gives you a 50cc and 70cc saw. I have run both the 440 and 460 and like the power to weight ratio of the 440. Plus...

Not sure if this will help, but I used a scrap car hood to move huge boulders from a creek bed up a hill to the house. The hood slides over rough terrain very well and can be pulled with an ATV/winch. Basically use the hood as a sled!

Thanks vincem77, found what I was looking for with the link you provided.

I did a search but didn't find the thread on how to mod the northerntool chain grinder. Anybody have the link handy.

I have the 361 that I use for firewood, that replaced my old 029. If you buy new from the dealer get the 24" with extra skip chain. It is cheaper to have the dealer upgrade to 24" bar and chain combo, mine was a free upgrade because I bought some other stuff. I purchased a 20" and 2 chains...

I wet sanded to 1200 grit, but could not get rid of all the black marks. I was worried about sanding threw the plastic trying to remove a few black spots. I then de-greased and shot it with krylon clear. I will post pics soon.

I have 2-ms260's both have this carb http://picasaweb.google.com/sthelen/Stihl?authkey=Gv1sRgCIiM5KHtornvEw&feat=directlink The IPL lists it as a WTE-1/2/4 http://picasaweb.google.com/lh/photo/BOEpx-D7rF0bXfygaJsRkA?authkey=Gv1sRgCIiM5KHtornvEw&feat=directlink I need to purchase a carb kit...

I have a ms260 with a carb that has both H,L screws on it. The only numbers stamped on the carb are Walbro WTE-643. I searched other posts and it seems to be a 194, how can I tell? I need the model number so I can order a rebuild kit of it. Thanks

I am looking for the 260 IPL for the different carbs. The entire IPL would be great!

The majority says its aspen or poplar, in a year or so it will be firewood. Thanks for the help!

Hello, I am sorry to keep doing this but a can't identify trees to save my life. I am clearing out my land of all the trees that have blown over or that are dead standing. I grabbed this today but it didn't have any leaves on it so I don't know what species of tree it is...

Thanks for the help...after a few google searches it looks to be red oak.