044

Hey guys and gals, I'm looking for a bigger saw for falling larger trees, bucking, and milling. 80cc and up, or something 70cc+ that's modded Stihl, Husky, or McColluch would be preferred. I'm happy with older saws, so long as they are in good condition! My budget is $500, bar included would...

Looking for a Stihl 70cc size chainsaw and narrowed it down to these models. I already have a 372xp but want to try out a larger Stihl (have a 026pro). Saw should be all oem. Not looking for rebuild. Doesn’t have to be a show queen but not one beat to crap. Let me know what you have. Thanks, Joe

Slant fin 044 cylinder, don’t know whether it’s a 10mm or 12mm, it was in a parts lot my buddy Ken has. He can get pictures of the bore tomorrow in better light, this is just the cropped pic of a group of pictures he sent me of stuff he wants to sell. He says he would like to get $100 for it.

Greetings, I found this saw at work the other day sitting in a puddle of b&c oil on a concrete floor. I had not noticed the saw before and inquired as to whos it was and when did we get it. It turns out that it was a donation and not much else was known about it. I told them that I would...

I just got an 044 for $60 and I need help identifying if it's the 10mm or 12mm version, I've read a bunch of thread and feel like I might known but I would like a more expert opinion, I attached some pics below, I think the piston may be a little scored on the skirt even though the compression...

Dad's 046 magnum has the original air filter (and everything else) that has never been changed, but he does clean it. Lately he said it's been losing power as he cuts with it. Says it's fine when he starts and then bogs down progressively. He decided he wanted me to put a new carb and filters in...

Have a relatively minor crack where the rear handle joins the footpad on an 044 and want to stop it from getting any worse. Is JB Plastic Weld any good or is there something better at around the same price? I was also thinking I would try and fill in under the footpad to reinforce it. Has...

Looking to trade my like-new 346xp oe with less than 10 hours of run time for an older 044 super or 440 mag. Would also consider 036 or 362. Mostly just looking for a bigger Stihl saw than 50cc. Must be in good condition, ready to work.

Not much of a thread but I am looking to mod my 044 muffler it has the divider with the 3 big holes, does it go to pry that out or does one need to cut it out? Also, behind the divider is a metal box with smaller holes surrounding the inlet to the muffler. Is it best to cut that out completely...

Basically I need some help, I've been offered an 044/440 hybrid, built out of almost entirely brand new and all genuine Stihl parts. Here's the list: -Brand new 440 crank case, bearings, crankshaft and seals -Brand new 12mm non decomp 044 Stihl piston and cylinder -Brand new starter housing...

hi guys, I'm wondering if anyone knows whether an 046 carb will fit an 044? And if there was a non compensating version of the 046 carb made? I'm building a ported fairly highly modded 044 and I'm worried about running lean, it'll be setup on the air filter side with a custom bell mouth and...

Hey guys, had some spare time today to check a few things on my badly abused 044 I bought. I have just removed the clutch from the saw to inspect what else is wrong, found huge amounts of oil soaked saw dust etc, but one thing has got me stumped here... I took the oil pump off and the worm gear...

Hey guys, I have some questions as I have just bought a very molested Stihl 044 which I will be rebuilding/replacing most parts. My questions are as follows; 1. The saw is what looks like a early model Stihl 044 WITHOUT a decomp valve, as I would like to replace the piston, cylinder etc, can I...

For sale- Serviced and tuned Stihl 044 ships with a New 24" Bar and Chain asking 600 shipped.

**Trade Pending** Thanks Hello, here's a few pics of the saw.. I did do a muffler mod last weekend and haven't gotten pics of that yet. I can grab some, no problem. I'd like to trade for an 066 or m660, 394, 395, maybe Dolmar, Makita, etc.... Consider anything but I'm trying to avoid...

I need a tank housing assembly for my 044 if you can help feel free to I'M me. Thanks a Stihlion Paul

Looking to find out the main bore and venturi bore for stihl 034 av super and stihl 044. I'd like to put a bigger carb om my 026 woody pro.

Found a small amish shop near me that has many new in the box older stihl models wanting to buy a new saw any particularly good models to look out for

I am selling a Stihl 038 Magnum 2 (II)chainsaw. The 038 Mag 2 is a 72cc saw. It became the 044. The saw is in great shape and runs great also. $375 without the bar and chain. It will handle an 18" to 28" bar with ease. The saw has great compression. I am selling to invest in a lighter saw...

Looking For Complete saws, salvage or parts for 044. I have 5 that I Would like to get going! Thank you