Homelite Chainsaws

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
you not bad I cheated---I have a comango

If you've run one long without earplugs, then you also have hearing trouble. What do you know about a "Cut Kwik"? Says Lombard on it, couple different spots, and I also have a fatter twin parts saw for that, a Dynamark. Both look like XL-12's, only black.
 
If you've run one long without earplugs, then you also have hearing trouble. What do you know about a "Cut Kwik"? Says Lombard on it, couple different spots, and I also have a fatter twin parts saw for that, a Dynamark. Both look like XL-12's, only black.

what did you say LOL---I don't know about a Cut Kwik sounds fun to have like any other Lombard Ive used---I have a Comango--Little lightning and 2 Ponies 1 running and 1 parts and all wear originally sold lockley around hear from the same shop still in business---do you have any info on the cut kwik---their wear lots of saws that look like the homies --- sears wards lombards just a hole lot of them
 
what did you say LOL---I don't know about a Cut Kwik sounds fun to have like any other Lombard Ive used---I have a Comango--Little lightning and 2 Ponies 1 running and 1 parts and all wear originally sold lockley around hear from the same shop still in business---do you have any info on the cut kwik---their wear lots of saws that look like the homies --- sears wards lombards just a hole lot of them

I stated my vast knowledge of it in the previous post. Loud as, well, hell, I imagine, and cuts OK. Even has some very primitive antivibe. Automatic oiler, no manual. Guessing mid eighties, probably earlier. 3.7 ci IIRC.
 
I stated my vast knowledge of it in the previous post. Loud as, well, hell, I imagine, and cuts OK. Even has some very primitive antivibe. Automatic oiler, no manual. Guessing mid eighties, probably earlier. 3.7 ci IIRC.

I thought they stopped making Lombards in the early to mid 70s
 
Super 2 reed.

The reed out of the Super 2 is standing open ever so slightly. Maybe 1/32", so it needs fixin'. I post a pic but it's too small to see.

Are those rivits or drive screws holding the reed and backup plate to the plastic?

How about if I drill & tap for a #4-40 round head screw to bear against the reed to help hold it shut?

T.I.A.
Carl
 
The reed out of the Super 2 is standing open ever so slightly. Maybe 1/32", so it needs fixin'. I post a pic but it's too small to see.

Are those rivits or drive screws holding the reed and backup plate to the plastic?

How about if I drill & tap for a #4-40 round head screw to bear against the reed to help hold it shut?

T.I.A.
Carl

I do have the manifold #A-69373, in case you haven't fixed your old one.
chain saw lady
 
The reed out of the Super 2 is standing open ever so slightly. Maybe 1/32", so it needs fixin'. I post a pic but it's too small to see.

Are those rivits or drive screws holding the reed and backup plate to the plastic?

How about if I drill & tap for a #4-40 round head screw to bear against the reed to help hold it shut?

T.I.A.
Carl

their drive screws but pressed in with heat---if you get them out just flip the plate over
 
770D lives again !!

Had this one for awhile..
guy i got it from said prob not run in 20 yrs.
snowy day in the shop thot i would check it out.
took bottom of carb off,cleaned it and fuel tank and the darned thing fired off and ran !!
have two top covers but dont know what one is correct.
also missing the recoil cover.
damn this thing is loud !!!!

<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/PZZ6mvhUu2c?fs=1&amp;hl=en_US"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/PZZ6mvhUu2c?fs=1&amp;hl=en_US" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
 
Cool !
Looks cold in there. Snow on the floor ?
Is that where you're working or did you just go out there to run it ?
 
Cool !
Looks cold in there. Snow on the floor ?
Is that where you're working or did you just go out there to run it ?

LOL !!! thats in my shop !! i had just came back in with the cam and stomped the snow off my boots :)
 
was hoping somebody could look at that video and see the two top covers and tell me what one is correct for that saw.
 
Had this one for awhile..
guy i got it from said prob not run in 20 yrs.
snowy day in the shop thot i would check it out.
took bottom of carb off,cleaned it and fuel tank and the darned thing fired off and ran !!
have two top covers but dont know what one is correct.
also missing the recoil cover.
damn this thing is loud !!!!

<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/PZZ6mvhUu2c?fs=1&amp;hl=en_US"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/PZZ6mvhUu2c?fs=1&amp;hl=en_US" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>

Beastly!
 
Here we go, I need, I need, I need. This CAD is hard on a feller!

I'm trying to get a C-7 going again. I got the saw from Outdoorliving247, the jug and piston came from Wildman. Thanks guys. :)

I need a good coil for it, and a clutch or just the clutch spider. I've tried to find a coil I could use on it but since it fits under the flywheel I'm not having any luck.

Any help would be most appreciated !!!!
 
Here we go, I need, I need, I need. This CAD is hard on a feller!

I'm trying to get a C-7 going again. I got the saw from Outdoorliving247, the jug and piston came from Wildman. Thanks guys. :)

I need a good coil for it, and a clutch or just the clutch spider. I've tried to find a coil I could use on it but since it fits under the flywheel I'm not having any luck.

Any help would be most appreciated !!!!

check your PM's
 

Latest posts

Back
Top