It's a light press fit. If it is loose, bugger it up slightly to make it tight.
Lombard chainsaws
- Thread starter MS460WOODCHUCK
- Start date
Help Support Arborist Forum:
It's a light press fit. If it is loose, bugger it up slightly to make it tight.
Just a Guy that cuts wood
ArboristSite Guru
Here's a picture of my lombard comango, I converted it to electronic ign. It has the haystack muffler,(it will make your ears bleed). I've been told they have weak crank seals, I think mine are bad bc i can get it to run cold, if I shut it off hot it won't pull any fuel out of the tank.
That goes inside the brass sleeve pointed toward the inside of the oil tank.
If I remember correctly, there is a small counterbore the flange part of the duckbill rests in.
[emoji108]
If I remember correctly, there is a small counterbore the flange part of the duckbill rests in.
[emoji108]
Some Lombard advertising from my collection.
Just a reminder:
I have a stack of Lombard IPLs I can scan if someone needs one.
Not that the part numbers are that useful but if something is missing from your saw you get an idea what it looks like.
Thanks Chainsawlady!!
I have a stack of Lombard IPLs I can scan if someone needs one.
Not that the part numbers are that useful but if something is missing from your saw you get an idea what it looks like.
Thanks Chainsawlady!!
Do you have an IPL for this little guy?
This it?
It's the only small Lombard IPL I have.
And, yes, Acres has some errors.
And, yes, Acres has some errors.
Just a Guy that cuts wood
ArboristSite Guru
Anything on 42 or AL4.2 D D is for Decompression Harrison Ohio made I can't find anything on Dynamark other than it's a Rebadged Lombard
Dynamark was some chain store brand.
Usually you see Lombard Governor or American Lincoln on the builder tag.
Usually you see Lombard Governor or American Lincoln on the builder tag.
Just a Guy that cuts wood
ArboristSite Guru
Looks like a Lombard But has A/V . ? I brought it because I have never seen one 
If it's not a Lombard what is it?
If it's not a Lombard what is it?
Lombard AP-42. Late model with AV. Not often seen.
I'd snagged that pup myself.[emoji106]
I'd snagged that pup myself.[emoji106]
Just a Guy that cuts wood
ArboristSite Guru
I am going to try and put the duck bill in this weekend . I am sure that's why it smokes . Ran it with out bar oil and no smoke .
I have to plug the decomp valve to be sure the seals are good but only bubble was from compression relief
was thinking of putting in seals anyway and just going over everything . Thats why I am looking for shop manual
If you or anyone knows of a seal # that will work that would help a lot
I have to plug the decomp valve to be sure the seals are good but only bubble was from compression relief
was thinking of putting in seals anyway and just going over everything . Thats why I am looking for shop manual
If you or anyone knows of a seal # that will work that would help a lot
Just a Guy that cuts wood
ArboristSite Guru
Fixed my pressure leak 
Had to make a new gasket
Now we hold vac/pressure 
Got a duck bill
put in no more smoke .
Looking forward to running a tank through and see what it's made of
Had to make a new gasket
Now we hold vac/pressure
Got a duck bill put in no more smoke .
Looking forward to running a tank through and see what it's made of
68cc of reed valve snort.
Should be an oil flow control valve on it somewhere.
I forget..........
Should be an oil flow control valve on it somewhere.
I forget..........
Just a Guy that cuts wood
ArboristSite Guru
If you find it take a picture I didn't see one and Thank you for your Help
I will keep looking for a manual
By the bar mount.
Start 1 1/2 turns out.
Start 1 1/2 turns out.
