husky 372 porting

[srcarr52]

I agree. The last two I did we're from MCW and they were great. I still like OEM better though.

I have one of those here that I haven't had a chance to even unwrap. The last kit I did was from Northwood and it worked out well but in out of the box from it would have ran pretty weak and not for long.

 

[parrisw]

I have one of those here that I haven't had a chance to even unwrap. The last kit I did was from Northwood and it worked out well but in out of the box from it would have ran pretty weak and not for long.

The last one I did I put it on a 371, unmodified, but with caber rings, seemed to run great.

 

[srcarr52]

the last one i did i put it on a 371, unmodified, but with caber rings, seemed to run great.

mcw?

 

[parrisw]

mcw?

Yes, had it the shelf for quite a while before I used it. Got another one back here now that I ported, main bearing let go and took out the piston and mushed up the squish a bit, but it'll clean up fine. Going to put it on a 362.

 

[o8f150]

this should answer your question:hmm3grin2orange::hmm3grin2orange:

<iframe width="560" height="315" src="http://www.youtube.com/embed/10aUUxoPl18" frameborder="0" allowfullscreen></iframe>

 

[catzr440sp]

372 porting

I guess so!!!! Thanx for the video!!

 

[parrisw]

this should answer your question:hmm3grin2orange::hmm3grin2orange:

372 ported be yours truly, ME! 50mm top end.

[video=youtube_share;r3RUi9xNgxI]http://youtu.be/r3RUi9xNgxI[/video]

 

[srcarr52]

I'll play. Here are a couple I've done.

[video=youtube;Mnq_BAbOfNw]https://www.youtube.com/watch?v=Mnq_BAbOfNw[/video]

 

[parrisw]

I'll play. Here are a couple I've done.

[video=youtube;Mnq_BAbOfNw]https://www.youtube.com/watch?v=Mnq_BAbOfNw[/video]

Wow, those are runners!

 

[half_full]

results http://www.arboristsite.com/chainsaw/168796-62.htm

I read through a few pages near the page number you posted. No final results. Is there a link to videos of the cuts and final results? A post or page number?

 

[Jimmy in NC]

372 ported be yours truly, ME! 50mm top end.

[video=youtube_share;r3RUi9xNgxI]http://youtu.be/r3RUi9xNgxI[/video]

Looks like it was a little camera shy! That thing is hauling on pretty good there.. what size bar is it wearing?

 

[parrisw]

Looks like it was a little camera shy! That thing is hauling on pretty good there.. what size bar is it wearing?

That was its first tank of gas, was a little lean on the low side, that's why it was hard to start.

Was a 24" bar, with semi chisel chain.

 

[mdavlee]

I read through a few pages near the page number you posted. No final results. Is there a link to videos of the cuts and final results? A post or page number?

Post 2451 has the results. I'm set up on 40 posts per page so I guess if you aren't it won't come out the same when you click the link.

 

[Jimmy in NC]

Seemed to be getting it done! I really like square for GTG speed but for general work, I'm going to get all of my saws some semi.

 

[half_full]

Post 2451 has the results. I'm set up on 40 posts per page so I guess if you aren't it won't come out the same when you click the link.

Thank you! 237 pages is alot to sort through.