Need more power from a ms290

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
brownstown

brownstown

ArboristSite Lurker
Joined
Feb 18, 2023
Messages
19
Location
Florence
Let me start out by saying I don't have a clue what I'm doing here. So I built a ms290 outta spare parts and pieces I had laying around so the saw isn't necessarily important to me so if we tear it up no big deal. I put a ms390 piston and cylinder on it, ported the muffler and I'm thinking about putting a ms460 carb on it just ti see how much more power I can get compared to a stock ms290. Does anyone have any advice or tips I could try to get it as close to a hot saw as I can? Would a base gasket delete be a good idea or not worth trying? Any advice would be appreciated.
 
singinwoodwackr
Joined
Jan 31, 2012
Messages
15,934
Location
“Free” State of Idaho
Ok, so…you like Frankinsaws, right? LOL
just keeping this thread going…might get interesting 😁

so, the 390 top end fit ok? No issues with cycling?
will the 460 carb bolt up ok?

in general…you have a “home” type saw, not a pro type so there won’t be much out there on this kind of drastic modding.

if it were mine…muffler mod, advance the timing a tad and that’s it.
but…anyone else? 🤪
 
brownstown

brownstown

ArboristSite Lurker
Joined
Feb 18, 2023
Messages
19
Location
Florence
Ok, so…you like Frankinsaws, right? LOL
just keeping this thread going…might get interesting 😁

so, the 390 top end fit ok? No issues with cycling?
will the 460 carb bolt up ok?

in general…you have a “home” type saw, not a pro type so there won’t be much out there on this kind of drastic modding.

if it were mine…muffler mod, advance the timing a tad and that’s it.
but…anyone else?
No cycling issues what so ever. It was running pretty rich so I opened the muffler up a little more because I couldn't get it to tune right. But now it seems to be running great.
 
a. palmer jr.
Joined
Apr 8, 2007
Messages
15,251
Location
Southern Indiana
When I do those I usually just put a piston/cylinder on it, along with a muffler mod. You can use a larger carburetor if you like but there's no such thing as a cylinder gasket delete on these saws, just a bit of Dirko on the bottom pan to seal it up. Just remember to use new crank seals and get the pan sealed good and it should run okay.
 
thompsoncustom

thompsoncustom

ArboristSite Operative
Joined
Jul 13, 2022
Messages
433
Location
iowa
last time I swapped a 390 top end on a 290 I ran a pop up since its a clamshell and could use the compression. if I had to do it again I would just braze the combustion chamber like I recently did on a wild thing.

the stock 290 muffler is horribly restrictive I would open it up to match the bore size (100%) or better yet cut the muffler apart and gut it and braze a deflector on the side. I hate the muffler on that saw.

the 460 carb might bolt up but either way doesn't look like it would take much to make it work. I ran a 460 carb on my ms260. is the venturi bigger on the 460 carb vs the 290? also not much point in swapping it if you haven't ported it yet.
 
Captain Bruce
Joined
Apr 5, 2015
Messages
936
Location
Michigan
When I do those I usually just put a piston/cylinder on it, along with a muffler mod. You can use a larger carburetor if you like but there's no such thing as a cylinder gasket delete on these saws, just a bit of Dirko on the bottom pan to seal it up. Just remember to use new crank seals and get the pan sealed good and it should run okay.
DITTO
 
nixon

nixon

ArboristSite Guru
. AS Supporting Member.
Joined
Nov 16, 2008
Messages
596
Location
West Sunbury Pa.
Not really a way to increase the power output of the saw . But , run a narrow kerf .325 chain/bar combo . I can’t directly site a source . But , I’ve read that they require 10-14% less power to run over a standard .325 . I’ve done it on 029/390 conversions and 350/346 conversions . Works very well .
 

Latest posts

Top