New years resolution

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
NORMZILLA44

NORMZILLA44

Addicted to ArboristSite
Joined
Apr 18, 2005
Messages
5,720
Location
Cazadero ca.
Just a work bench, yeah a bad ASS!!!!!! Work bench:msp_thumbsup: Thats a nice piece of wood dude:rock: And you know I am a fan of your saws, they really make the bench what it is:msp_thumbup:
 
bryanr2

bryanr2

Addicted to ArboristSite
Joined
Dec 31, 2010
Messages
6,005
Location
Foothills of TN
BEAUTIFUL piece of wood and your craftmanship with the finish! I'd leave it for a place to display the saws or drink a cold one when out in the shop. Too nice to work on. Great job. Wish it was mine.
 
Timberframed

Timberframed

ArboristSite Guru
Joined
Jun 1, 2010
Messages
637
Location
Carversville, PA
That is a great work indeed. I can't wait to replace the plywood top for the turret radial saw's bench, solid piece of Red oak 22' x 2' x 2". For a resolution I will try to find out how to jam up the computers that keep sending me these junk e-mails! Can't they figure out that someone like me isn't even remotely interested in any of the dung they keep trying to push on us? It has reeked havoc on two of my pc's. 200 cc's do tell more.
2690610340105432928S600x600Q85.jpg
 
Last edited:
Talltom

Talltom

ArboristSite Operative
Joined
May 2, 2011
Messages
127
Location
Fairfax Virginia
Hey Sachsmo, a beautiful workbench like that deserves a better beer than Busch! I did not see any spalting in the original photos - it looks pretty solid all the way through. There is a lot of the pith in the center - has that started to separate or crack at all?

Timberframed - That slab will make a beautiful bench top, but how are you going to dry it and keep it flat? Seems like alignment would be critical for a saw bench. You may want to consider putting the slab slightly below the height you want and using small stickers every couple feet to bring the wood you're sawing up to the proper height. The stickers could be easliy adjusted over time to make up for any movement in the slab.
 
Old Blue

Old Blue

ArboristSite Guru
. AS Supporting Member.
Joined
Apr 3, 2010
Messages
684
Location
San Diego, CA
Great looking workbench Sachsmo

Those must be some beefy brackets holding that up. It sure looks like your finish is a great choice and is holding up well. Thats a great looking piece of wood, I want one!

Old Blue
Taxed to infinity.......and beyond! in
Kali-bone-ya
 
betterbuilt

betterbuilt

I build stuff from milled slabs
Joined
Jan 14, 2010
Messages
1,448
Location
Hammondsport, ny
Talltom, I was going to router plane it then immediately add a bunch of 3" angle iron pieces bolted to the underside. Like every 20".

With the angle I'm seeing big Black stains.


I was using a peice of walnut outside for a temporary table. I left some bent nails and other stuff on it and it rained. The next morning there were big black stains(not rust stains).
 
Talltom

Talltom

ArboristSite Operative
Joined
May 2, 2011
Messages
127
Location
Fairfax Virginia
The angle iron should keep it from cupping, but not sure how it would stop twist or bow. I added a base cabinet and top to the left of my radial arm saw to support long boards a couple years ago. My saw is on legs and about 5 inches above normal counter height, so I had to raise the level of the supports above the top of the cabinet. I made two 3x3 beams which are hinged at the wall and supported above the counter top near the outside end with carriage bolts screwed into T nuts. They're adjustable on both ends and can be pivoted up and out of the way when not in use (though I seldom do this). This turned out to be beneficial for two reasons - It's easier to adjust a couple small pieces to be level with the saw table, and I don't have to remove all the crap that accumulates on any horizontal surface in my shop in order to use the saw.

These issues will be even more important with the size slab you're going to use. So I amend my recommendation. Set the slab at least 3 inches below the level of the saw table and use temporary or permanent supports to raise long boards. This will allow easy adjustment should the slab move after installation as well as better use of the surface.
 

Latest posts

Top