Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS
- Thread starter Work Saw Collector
- Start date
Help Support Arborist Forum:
Work Saw Collector
GTG Coffee Maker
When Did you rename? I'll be lost for months now. :hmm3grin2orange:
Work Saw Collector
GTG Coffee Maker
Repped
How have you guys managed without me?
Cutting some 36 inch oak today, and yesterday. Have to work on 3 saws first.
Been really busy, doing nothing.
I've got the lake cleaned a bit, a much nicer location now.
I'll check back as soon as I can.
Cutting some 36 inch oak today, and yesterday. Have to work on 3 saws first.
Been really busy, doing nothing.
I've got the lake cleaned a bit, a much nicer location now.
I'll check back as soon as I can.
Hedgerow
HACK
How have you guys managed without me?
Cutting some 36 inch oak today, and yesterday. Have to work on 3 saws first.
Been really busy, doing nothing.
I've got the lake cleaned a bit, a much nicer location now.
I'll check back as soon as I can.
Just getting by... Howdy Dan!!!
How have you guys managed without me?
Cutting some 36 inch oak today, and yesterday. Have to work on 3 saws first.
Been really busy, doing nothing.
I've got the lake cleaned a bit, a much nicer location now.
I'll check back as soon as I can.
just barely. we've been on starvation diet just getting by on your infrequent poasts. is that oak vertical or horizontal? live or dead? be careful and cyhoya
Hedgerow
HACK
Hey Jerry, I located filter elements and a top cover for that 3.7... Now, with .325 chain, how big a bar do you suppose it could handle? Ethan wants to use it as his "BIG" saw.:hmm3grin2orange: I burried the 18" bar in a 30" red elm log last night, and it just plugged right along. Actually has a little torque... Good thing too, cause it ain't got any RPM's!!!
Hey Jerry, I located filter elements and a top cover for that 3.7... Now, with .325 chain, how big a bar do you suppose it could handle? Ethan wants to use it as his "BIG" saw.:hmm3grin2orange: I burried the 18" bar in a 30" red elm log last night, and it just plugged right along. Actually has a little torque... Good thing too, cause it ain't got any RPM's!!!
glad to hear it. where'd you locate them in such short order? is that chain a .05 gauge? only published info i can find on this saw is the user/ipl manual. its pretty sketchy concerning bar/chain size and definitely says nothing regarding rpm's. guess you've noticed it only has the L and rpm adjustment screws, no H adjustment. was wondering what H adjustable carb would fit that thing. what rpm you running at? i'm still waiting for my air filter to arrive so i can try it out in wood. still got to take it down and clean it up. maybe we can race, eh?
Hedgerow
HACK
Yeah, I noticed there wasn't a high adjustment. The low has about a ~20% effect on the way it runs at full throttle, so I put it in a vise, gave it hell, and got some blubber at full throttle. Still smooths out in the cut. Then set the idle screw to the minimum it would stay idling at.
The chain on it was an anti-kickback chain, so I ground off the humps and filed teeth and guides accordingly. Like a dumbass though, I forgot to mic the drivers to see if they were .050... I believe they are though. And yes, we will have a turtle race at the next GTG!!!
My decals also came in for the 372!:msp_thumbup:
nice. i figure we'll give them other 61's a run for their money given as these are reed valves and therefore easily modded:msp_wink:
Hedgerow
HACK
I might be able to figure it out, but as of now, I don't know crap about the carb on this thing. Any advise would be appreciated...:hmm3grin2orange:
Stumpys Customs
Stumpbroke
Yeah, I noticed there wasn't a high adjustment. The low has about a ~20% effect on the way it runs at full throttle, so I put it in a vise, gave it hell, and got some blubber at full throttle. Still smooths out in the cut. Then set the idle screw to the minimum it would stay idling at.
My decals also came in for the 372!:msp_thumbup:
Lookin good Matt!!!!!!!!
firefighter33
ArboristSite Guru
Hope u have a Stumpbroke 460 decal comin stumpy. I'm trying like hell to find one I can afford. I'd love another saw done by u!! The 371 is running great! Got about 4 1/2 gallons threw it seems like it keeps getting stronger !!
!!
Hedgerow
HACK
Hope u have a Stumpbroke 460 decal comin stumpy. I'm trying like hell to find one I can afford. I'd love another saw done by u!! The 371 is running great! Got about 4 1/2 gallons threw it seems like it keeps getting stronger
Maybe it's just me, but I swear the Stihl ultra makes the break in time 3X's as long...
Stumpys Customs
Stumpbroke
Hope u have a Stumpbroke 460 decal comin stumpy. I'm trying like hell to find one I can afford. I'd love another saw done by u!! The 371 is running great! Got about 4 1/2 gallons threw it seems like it keeps getting stronger
Sweet, give it hell!!!!!!!
Good things happin with time!!
Hedgerow
HACK
I tried to get a reading on that saw again, but my POS compression gauge bounces up around 195 lbs and bleeds off, so while I crank, the damn needle won't just ratchet up and stay...
I'll find a better gauge...:msp_angry:
sunfish
Fish Head
'Stump Broke Club'
I'm building a 372xp, but I just might let Stumpy finish it. :msp_biggrin:
I'm building a 372xp, but I just might let Stumpy finish it. :msp_biggrin:
That's why you don't break a saw in with synthetic.
Hedgerow
HACK
Stumpys Customs
Stumpbroke
Don't tease me Don!!!!
Got's me a 576xp to build fer a local Logger in the shop right now. Gotta see what I can do with the strato saws
