Look around downhill from the basement floor level. Extra wet spot.
Later this summer it may be where the grass is still green is where it comes to daylight.
Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS
- Thread starter Work Saw Collector
- Start date
Help Support Arborist Forum:
Look around downhill from the basement floor level. Extra wet spot.
Later this summer it may be where the grass is still green is where it comes to daylight.
Scott Kelly
Silverpsd_06
Making a little progress.. New meteor piston and caber rings. Cleaned up the piston ports, does anyone know if this is actually beneficial? I do it anyways but have always wondered. Squish is set from factory @ .031". I've found that card stock off of stickers brings it right to .019". A little tight but I'd say still acceptable for that small of a bore or am I asking for trouble?
Homelite410
Hack with a CNC Mill
I run squeak at .018". No problems in 3 years.
Scott Kelly
Silverpsd_06
Well the intake is pretty well in the shape that I want it.. Might do a little more smoothing but I did cut through so better judgement says it'll be fine while the boot can still cover it up[emoji58]
Hedgerow
HACK
What is your intake duration?
Well the intake is pretty well in the shape that I want it.. Might do a little more smoothing but I did cut through so better judgement says it'll be fine while the boot can still cover it up[emoji58]
Try not to remove material from the floor if you can avoid it.
cobey
Addicted to ArboristSite
Something I found........ An 81dl bar (echo or Mac) is a 23" bar
A 84 driver bar (husky) is about 24"
A 70 driver bar is about 19"
A 72 driver is Close to 20"
That's what may tape says anyways
A 84 driver bar (husky) is about 24"
A 70 driver bar is about 19"
A 72 driver is Close to 20"
That's what may tape says anyways
Scott Kelly
Silverpsd_06
I don't have a degree wheel to put on it but I didn't take much of anything off the bottom
probly about 105 feet from the basement. you got a direction? stake out where the 100' mark is. get a witching stick or welding rod or whatever and have at it.
The 'Coppertone' girl. Hooskeybarney with a bad sunburn.
What is the cover at the top part of the muffler for?
A home made muffler brace. We tidied it up with proper flat and lock washers.
Stihl decomp on a Hoosky. Extra clearance so it don't hang up.
Ran him cutting up a large branch out of the huge oak down the street. Fell out last night. Bar/chain rather much done for.
I have a new Oregon 20" K095 but it is way too short for this saw!
What is the cover at the top part of the muffler for?
A home made muffler brace. We tidied it up with proper flat and lock washers.
Stihl decomp on a Hoosky. Extra clearance so it don't hang up.
Ran him cutting up a large branch out of the huge oak down the street. Fell out last night. Bar/chain rather much done for.
I have a new Oregon 20" K095 but it is way too short for this saw!
It also has to do with the space from the sprocket to the bar studs.Something I found........ An 81dl bar (echo or Mac) is a 23" bar
A 84 driver bar (husky) is about 24"
A 70 driver bar is about 19"
A 72 driver is Close to 20"
That's what may tape says anyways
For example; 20"/70 dl is Mac, Homie, Remy old school saws. 20"/72 dl is Hoosky, Echo and the newer stuff.
Explains why it was mashed somewhat flat(ish)![emoji6]
Scott Kelly
Silverpsd_06
Can anyone explain what different durations do to the saw? Like longer exhaust, longer intake ect..
WKEND LUMBERJAK
Addicted to ArboristSite
That bar won't fit any whoo it will take a large husk same as the 2 jreds. I have a 42 " bar for it. Used it once or twice just because.
WKEND LUMBERJAK
Addicted to ArboristSite
cobey
Addicted to ArboristSite
The echo 590 use a 70 dl 20" bar. I run an 84 dl 24" LG mount husky bar and a 81dl 24" echo bar on it ...... adjustment is different but they both work.
I ran a 72 driver 20" on it also.
I run a LG mount husky 24" bar on my Lombard AP 42
(With adapters) it uses a 84 dl chain
Scott Kelly
Silverpsd_06
Where could I find this fellow?
Homelite410
Hack with a CNC Mill
You should just call him. Please...
Scott Kelly
Silverpsd_06
Right..
Homelite410
Hack with a CNC Mill
Matt= hedgerow
