Want to Buy Shindaiwa 695 Piston Rings

[ChainsawmanDan]

I need piston rings for Shindaiwa 695 part number 22150-41210. I have the piston just need the rings. Thanks

 

[Woodslasher]

If you can tell me the thickness of the old ones I should be able to direct you to a set of Cabers that will work.

 

[ChainsawmanDan]

If you can tell me the thickness of the old ones I should be able to direct you to a set of Cabers that will work.

Ok That would be great. I pulled one off this morning so I will measure it when I get home later tonight. I’m at work right now

 

[ChainsawmanDan]

Ok That would be great. I pulled one off this morning so I will measure it when I get home later tonight. I’m at work right now

Thickness of the rings are 1.50 mm

 

[ChainsawmanDan]

Thickness of the rings are 1.50 mm

The Width of the piston ring(right) seems a little bit thinner than the one from my Stihl 390 on the left. I can measure the width if needed

 

[Woodslasher]

It could be that the Shindaiwa rings are just severely worn, but idk. I was thinking a Stihl/Husky ring of the same o.d. might work, but it’s looking like I may be wrong. If the 390 ring is the same diameter, maybe try that on the Shinny piston and see if it will fit in the cylinder. If it won’t, I‘m guessing you’ll just have to wait for n.o.s. ones to pop up on eBay.

 

[TLG]

The 695 rings are narrower than the Stihls although thickness is correct @1.5mm. They are also etched with a T for top just like your old one as shown. You can still order new rings from most parts houses and Shindaiwa dealers. About $10 a piece. Hope this helps.

 

[ChainsawmanDan]

The 695 rings are narrower than the Stihls although thickness is correct @1.5mm. They are also etched with a T for top just like your old one as shown. You can still order new rings from most parts houses and Shindaiwa dealers. About $10 a piece. Hope this helps.

Ok I will try to call some places tomorrow. Thank you

 

[ChainsawmanDan]

It could be that the Shindaiwa rings are just severely worn, but idk. I was thinking a Stihl/Husky ring of the same o.d. might work, but it’s looking like I may be wrong. If the 390 ring is the same diameter, maybe try that on the Shinny piston and see if it will fit in the cylinder. If it won’t, I‘m guessing you’ll just have to wait for n.o.s. ones to pop up on eBay.

Yeah I was thinking NOS is the only way I can find them. I know caber at one time made them as well but I think they are obsolete now.

 

[TLG]

Sent you a pm

 

[TLG]

Dan, Click on the red email icon in the upper right side. That is a PM notice. I gave you 3 or more options. Good luck

 

[bosslock]

Hey Dan where did you get the piston from?I ordered piston and barrel from my local dealer and it has 580 on the barrel and is about 3mm smaller. When i look up the part number it says its for the 695 and a few models under it like a 570 etc
cost me a few hundred dollars too ><

 

[ChainsawmanDan]

Hey Dan where did you get the piston from?I ordered piston and barrel from my local dealer and it has 580 on the barrel and is about 3mm smaller. When i look up the part number it says its for the 695 and a few models under it like a 570 etc
cost me a few hundred dollars too ><

Ebay

 

[ChainsawmanDan]

Ebay

The 695 had 2 different pistons I believe. One with a 11 mm wrist pin and one with 12 mm. Both 49 mm.
I found a piston and rings for mine by luck because they have been obsolete for 20 years almost. Pretty sure you can put a 575 jug on a 695 but you will loose some cc

 

[ChainsawmanDan]

Cherokee Small Engines Gaffney SC
864-487-4038
give them a call that’s where I found my piston rings from a dealer in West Virginia they got a Interface look up to different Shindaiwa dealers in the US. If there’s a new old stock part that’s still in stock at any of these places they will let you know just give them the part number