What is this Husqvarna chainsaw?

[2strokeoil4blood]

Came into possesion of this today. What is it?!

 

[Bob Hedgecutter]

Thats where you do a bit of investigative detection work.
Does it have a two piece top cover?
Manual oiler button?
Location of oil/fuel caps.
Muffler style and shape.
Clutch cover style and position over handle mount.....

What do you "think" it might be?
Hope you like em big?

If you already own it- and you are wanting rid of it- I will give you $50 for it if you cover postage!

 

[2strokeoil4blood]

Thats where you do a bit of investigative detection work.
Does it have a two piece top cover?
Manual oiler button?
Location of oil/fuel caps.
Muffler style and shape.
Clutch cover style and position over handle mount.....

What do you "think" it might be?
Hope you like em big?

If you already own it- and you are wanting rid of it- I will give you $50 for it if you cover postage!

I think its a 2100 or something similar. I do want rid of it

 

[Bob Hedgecutter]

I think its a 2100 or something similar. I do want rid of it

I think you might be close.
So how did it come into your possession? Looks like it has been sitting in an open bay shed for a good while- below perching birds.
Does it run- does it turn over?

 

[Gord404]

should be a small tag plate if is still there on front part of the clutch side casing beside the muffler, if its missing my best guess is a 2100, 2101 because of the hand oiler bonus.

 

[Huskybill]

it’s a 2101xp/2100xp hand Oiler It for sure a 100 cc. Monster. Run a beast today.

 

[RED-85-Z51]

I love it...

Sent from my SM-G996U using Tapatalk

 

[Huskvarna hotellgäst]

Late 1980s 2100.

 

[Bob Hedgecutter]

A very shagged late 80's 2100.........



What do you recommend?
Acid- or fine sandpaper?

 

[Woodslasher]

A very shagged late 80's 2100.........

View attachment 912098

What do you recommend?
Acid- or fine sandpaper?

What're you talking about? All I see are some finger ports for mo' powa!

 

[Huskvarna hotellgäst]

A very shagged late 80's 2100.........

View attachment 912098

What do you recommend?
Acid- or fine sandpaper?

I don't recommend reusing it. IIRC the ring gaps are either side of the intake port so whatever you do to is likely to end in a broken ring,

 

[Bob Hedgecutter]

I don't recommend reusing it. IIRC the ring gaps are either side of the intake port so whatever you do to is likely to end in a broken ring,

Mate- take note of the laughing emoji!
Reusing is NOT a consideration and the asking for a recommendation was very tongue in cheek!

 

[Woodslasher]

Mate- take note of the laughing emoji!
Reusing is NOT a consideration and the asking for a recommendation was very tongue in cheek!

Get it rechromed or get the Duke's 2100 p/c kit. It's gotten the thumbs up from a lotta respectable guys.

 

[Bob Hedgecutter]

What're you talking about? All I see are some finger ports for mo' powa!

Whatever it ate, most of it is now embedded in the squish band of the top of the cylinder- though some remains entrenched in the sides of the piston top.

 

[Huskybill]

I don’t the hone will remove those score marks. That’s some heavy galling.

New cylinders and pistons on eBay.

 

[Woodslasher]

Whatever it ate, most of it is now embedded in the squish band of the top of the cylinder- though some remains entrenched in the sides of the piston top.

How's the big end bearing look/feel? That looks like my neighbor's 045 that had the big end bearing let go.

 

[Bob Hedgecutter]

How's the big end bearing look/feel? That looks like my neighbor's 045 that had the big end bearing let go.

To be honest- top and bottom rod bearings felt reasonable for the saws age and main bearings felt okay without pulling clutch- oiler nor flywheel.
I just pulled the cylinder (a story on its own) to see what was up with the low compression- fingers were crossed for just stuck or worn rings ( but it IS a thin ring piston) as with the muffler off, the exhaust side of the piston looked sweet.......

 

[Huskvarna hotellgäst]

Mate- take note of the laughing emoji!
Reusing is NOT a consideration and the asking for a recommendation was very tongue in cheek!

Oh yeah! Now I see it

 

[GeorgiaVol]

JB weld the gashes and sand back smooth.

 

[Bob Hedgecutter]

JB weld the gashes and sand back smooth.

The saw is in New Zealand, not Australia- no JB Weld will be harmed.