Search results

Just because you're paranoid it doesn't mean they're not out to get you . It's a flat tire . If he wanted to screw you I doubt very much that would have been his choice . Good luck Matlock .

Thinking of Your Father My thoughts are with you and your father Calvin . I will say a prayer to give you both strength .

You poor guy , my heart goes out to you .......not ! You gotta like it when that happens , right place , right time . Way to go .

Rings are cheap It's fortunate you realized the ring was broken before completing the assembly . My method is ; place all rings on piston , then starting with upper ring , make sure it is well lubed and installed correctly ,slip lubed cyl. over piston and compress ring into groove with finger...

Paint Hello lesorubcheek , I purchased the paint at "Lordco" , a automotive parts chain in Canada . I'm not sure what the American equivelant store would be . Wiped all parts with gunwash prior to priming with super krorypon (sic) and then sprayed with acrylic enamel "Hot Licks C " . Mae...

Assembly Finished Finished putting the Poulan together , well worth doing as it runs well and you can feel it pull for a little saw . This little beauty is like new now . Needs a little carb adjustment for fine tuning and then cut wood .

Well I'll be Darned That is an excellent link you found and posted . Not to blow my own horn but if you read the 3rd and 4th paragraph on page two it is almost verbatum to what I said in the 5th post . I must have been paying attention that day . Good luck with your trouble-shooting and let...

You're the man Ray ! Thank you for answering that question Ray . Now I can continue with the assembly . :cheers: +1 to you .

Anyone Able to Answer This ? Is anyone able to answer the question I posed in post #21 of this thread ?

Not Clear On The Concept ? If you're not sure about the question I posed all you have to do is ask for clarification although those that know a bit about saws will understand . If you look at the pics I have posted it will become clear to you that the connecting rod is orientated such...

Wrist Pin Installation ??? Please help with this one : I'm in the shop about to put the new piston , wrist pin , clips , rings and cylinder on to cases and I noticed the wrist pin differs from one end to the other end . One end of the pin is solid whereas the other end of wrist pin is hollow ...

Breaker Points Operation Correctly adjusted points will be in full contact with each other for the majority of each crankshaft revolution . The breaker cam lobe opens the points ( no contact ) and disrupts the flow of voltage through the coils primary windings . This collapsing magnetic field...

Manual oiler Rod As Modifiedmark said the manual oiler rod has to extend down from button into the pump housing , must fit into small hole in red end cap as shown i n picture below .

Muffler Mod Details Could you provide any details or pictures of how you modded the muffler on that Poulan 2000 ? See thread entitled " 2 Cycle Engine Assembly 101 " for details of what I'm up to . Perhaps you can comment on the muffler pic I posted as to if and how to modify it . Thanks .

Getting Closer I apologize for the effectiveness of the two previous posts . I'm trying to relate the oil pump and bottom end assembly of the little Poulan with pictures . Not being too computer savy it takes a little practice to get the pictures of correct size and order :dizzy: . I'm going to...

Hope this works

Poulan Bottom End and Oil Pump G]

posting test

Ready to Assemble Well , I painted all the parts , de-burred the new cylinder , polished the crank , replaced the case seals and started to re-assemble today . Made an interesting find : I'm replacing the oil inlet valve for the pump ( it's actually a tiny one way check valve and has a little...

Centrifigal Clutch Engine Rpm triggers centrifigal clutch to engage . If idle is set to fast the weights overcome spring tension and drive is transmitted from crankshaft to sprocket drum and chain . I suppose it would be possible to have weak or broken clutch springs but I doubt that is your...