gregz
ArboristSite Guru
Boy O Boy I sure hope this saw meets his expectations or I'll be :censored: toast
Mint 090
- Thread starter blsnelling
- Start date
Help Support Arborist Forum:
What a piece of crap, lol:greenchainsaw:
I see that it is delivered. Where are the pics and video, man?
Yes it is, and it's a thing of beauty! I just ground off about half of the teeth left on the original chisel chain, setting the rakers, and cleaning out the gullets. I'm fixing to go mount the B&C, warm it up, tune it to specs on 32:1 Klotz R50 and get you guys a video
stinkbait
Addicted to ArboristSite
Yes it is, and it's a thing of beauty! I just ground off about half of the teeth left on the original chisel chain, setting the rakers, and cleaning out the gullets. I'm fixing to go mount the B&C, warm it up, tune it to specs on 32:1 Klotz R50 and get you guys a video
Hurry up! I have to leave work early today, and won't be able to watch it until Monday if I miss it now.
sefh3
Addicted to ArboristSite
Yes Brad we are all waiting.
I'm back inside and will get them up ASAP. I'm sweating like a pig working for you guys
Henry G.
ArboristSite Guru
You were jonsin so bad for that thing maybe I should held out for another 50 bucks off on the 357?:greenchainsaw:
It wont get it until Tuesday...
It wont get it until Tuesday...
FATGUY
Addicted to ArboristSite
- Joined
- Jun 2, 2008
- Messages
- 6,535
- Reaction score
- 1,537
I'm back inside and will get them up ASAP. I'm sweating like a pig working for you guys
my heart goes out to you, poor guy, having to mess around with your own 090 :hmm3grin2orange:
gregz
ArboristSite Guru
Dibbs
ArboristSite Guru
Heres another photo
The best thing about sacrilege is that you can always repent later!
Take my 090 for instance, I had it at 210 psi cold after a bout of sacrilege with the cylinder in a four jaw chucked lathe.
I repented and brought it to a more "reasonable" level.
I'll see your 150 and raise you 40!
Lovely saw Brad, congratulations on joining the 090 club!
Henry G.
ArboristSite Guru
I'm at work. If I'm earning money I MUST be working
The video will be along shortly.
sefh3
Addicted to ArboristSite
Nice looking setup Keep the pics coming!!!!!
You can sure tell I don't have any experience running this saw, lol. You'll just have to forgive my inexperience. Carb setting specs on this saw are 11,000 with the governor disabled. I have it set at 10,600. With the governor enabled it should be tuned to 7,500-8,000. I'm only turning 6,xxx. It's making the saw very difficult to cut with. I have to put way more load on the saw than I should have to in order to get it to clean out and run right. That's also what's making it surge up and down. For the last two cuts I disabled the governor and you can finally see what it should run like. I'll get the governor adjusted shortly.
Also, this is not a good noodle making saw. It packs up very easily. Oh well, who cares anyway? The saw starts like a dream. I haven't even used the decomp yet. It idles as slow as mollasses in January and has good throttle response. I'm VERY happy with my new "toy"
You'll have to give it a few more minutes to finish processing on their end.
<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/cHW8u2qmTOI&hl=en&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/cHW8u2qmTOI&hl=en&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>
Also, this is not a good noodle making saw. It packs up very easily. Oh well, who cares anyway? The saw starts like a dream. I haven't even used the decomp yet. It idles as slow as mollasses in January and has good throttle response. I'm VERY happy with my new "toy"
You'll have to give it a few more minutes to finish processing on their end.
<object width="425" height="344"><param name="movie" value="http://www.youtube.com/v/cHW8u2qmTOI&hl=en&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/cHW8u2qmTOI&hl=en&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>
Henry G.
ArboristSite Guru
Crap all I can see are red x's.
sefh3
Addicted to ArboristSite
NICE SETUP.
Go drink a few. It's warm out there.Thanks for the video's.
brncreeper
Addicted to ArboristSite
sweet 090 Brad.
Not trying to hijack your thread, just uploading some pictures from today.
Not trying to hijack your thread, just uploading some pictures from today.
Last edited:
sweet 090 Brad.
Not trying to hijack your thread, just uploading some pictures from today.
Yehaa!
I went out to tune the high end with the governor enabled. With the spring all the way back as far as it will go I'm still turning 6,900. What's the best solution here, you 090 gurus. Dibbs Tuning Guide
