Warped5
WingNut
Hmmm ..... Where is it? I'm sure one of us would fetch it for you!
How do the pix look? If it wasn't TOO far, I'd sure take a chance on it.
Sachs Dolmar Chainsaws Thread
- Thread starter pioneerguy600
- Start date
Help Support Arborist Forum:
Hmmm ..... Where is it? I'm sure one of us would fetch it for you!
How do the pix look? If it wasn't TOO far, I'd sure take a chance on it.
Hmmm ..... Where is it? I'm sure one of us would fetch it for you!
How do the pix look? If it wasn't TOO far, I'd sure take a chance on it.
got a son-in-law that lives there. he doesn't know anything about chainsaws. told him to get the guy to start it. if it runs buy it.
Warped5
WingNut
Lucky for you ..... remember, no pix means it never happened! :msp_thumbsup:
will post when/if it happens
couple of sweet runners,
did you slab that workbench yourself? nice.
Warped5
WingNut
Warped5
WingNut
Dolmars Rock
Yikes! Agreed! :msp_w00t:
Where did you get that aluminum material for the shelf brackets?
This is the log I got my 3 shelves from;
Don't have any pics millin' that workbench. The guy who owned the tree insisted I take a slab. (He got 6) roughly 9 ft by 24-28 inches wide. The log was 19" long, but at 3.125" thick, we could not lift them @ 19 ft so we cut 'em in half. The butt of the log measured 38" so we had to freehand quite a bit off since my mill would only go a bit over 28 inchs. It was a cold rain when we did the last 1/2 slab (my bench) sad thing is half the log ended up as firewood.
Don't have any pics millin' that workbench. The guy who owned the tree insisted I take a slab. (He got 6) roughly 9 ft by 24-28 inches wide. The log was 19" long, but at 3.125" thick, we could not lift them @ 19 ft so we cut 'em in half. The butt of the log measured 38" so we had to freehand quite a bit off since my mill would only go a bit over 28 inchs. It was a cold rain when we did the last 1/2 slab (my bench) sad thing is half the log ended up as firewood.
This is the log I got my 3 shelves from;
Don't have any pics millin' that workbench. The guy who owned the tree insisted I take a slab. (He got 6) roughly 9 ft by 24-28 inches wide. The log was 19" long, but at 3.125" thick, we could not lift them @ 19 ft so we cut 'em in half. The butt of the log measured 38" so we had to freehand quite a bit off since my mill would only go a bit over 28 inchs. It was a cold rain when we did the last 1/2 slab (my bench) sad thing is half the log ended up as firewood.
A sadder thing would have been for it to stay in the woods. Nice bench, nice nice saws.
166
FYI- looks a little 'salty' but a 166 in my neck of the woods ? wow. too rich for me.
enjoy.
SACH DOLMAR 10 HP MODEL 166 CHAINSAW
FYI- looks a little 'salty' but a 166 in my neck of the woods ? wow. too rich for me.
enjoy.
SACH DOLMAR 10 HP MODEL 166 CHAINSAW
Bertwhistle
ArboristSite Lurker
Help with a manual or IPL for a Dolmar/Sachs 123 please?
I have posted on the manuals thread already but had no luck as yet.
I would be grateful for any ideas on where I could obtain one please.
Many thanks
Neil
I have posted on the manuals thread already but had no luck as yet.
I would be grateful for any ideas on where I could obtain one please.
Many thanks
Neil
For an IPL go to the top of the page, look for Chainsawr.com, its the red advert for chainsaw parts. Open that page and you will see a place to click on for, "illustrated parts". The rest is just selection.
Bertwhistle
ArboristSite Lurker
Little Al
Addicted to ArboristSite
SD Bar Plates
Hi, does any one have to sell a set of bar plates for a117. or could point me in the direction of obtaining some Thanks.
Hi, does any one have to sell a set of bar plates for a117. or could point me in the direction of obtaining some Thanks.
