tree md
Addicted to ArboristSite
Vermouth is kinda like triple sec... A waste of space...
Thu (as far back as I can remember....shut up Lovey) we worked in the thick woods way back off the road and found 2 other tree services working in properties contiguous to ours. One was a 5 man crew and a big fat guy pulling up the climber. The other was a 4 man crew also taking trees down and spiking all the way up.
We show up and they are all watching me by myself (gm at dump) shooting a beanie up a tall maple removal over the house. Other climbers are still humping up. I am taking my time setting up my wraptor. I head up and stop at every branch and either drop it or send it down off my climbing line crotched above my head. The gm is back and detaching them.
I get to the top and butt hitch the top and he lowers it down and presto we got a stripped pole. I turn around and they are still heading up their trees and they and their crews keep staring at the old man in the top. Chunked and butthitched into a block and slammed the stick. Did a second one the same. They are humping brush up a ravine and we are going down hill. They humping wood up hill and we dingoing down into a truck below a stone wall.
Next day we are working between 2 huge Victorian homes in a tight drive taking over 10 inch dia deadwood out of the over 100 foot top of 4 foot diameter Red oak that is over one roof and all over a model train set that runs all over the yard including a miniature pond and bridges and mini buildings etc etc. No damage but it was tense esp the very top I had to climb outta the bucket and toss the tops away from the RR.
Saturday we loaded up some firewood (believe it or not) 95 degrees 95 humidity and delivered the cord. We looked at a couple of jobs and then said the hehll with it.
Diary of a madman
Nice! You could eat off of that thing.
Got down to bidness with the new cummins. Should have her bolted up tomorrow. Waiting on some belts and hoses from Bandit and pilot bearing for the clutch being rebuilt. Should have everything rolling Wednesday at the latest. Anyone know the break in procedure for a 4BT 3.9 liter?
Bet you know how to figure that out before we can respond.
Jeff
Break in procedure? Yes. Pack the bearings with hummous and fill the crankcase with babaganouj. Run it at 2grand for twenty minutes then open up a bag of pita bread and dig in.
No really, ask the guys who you got it from but generally run it 2 grand for 20 minutes is par for most motors.
Break in procedure? Yes. Pack the bearings with hummous and fill the crankcase with babaganouj. Run it at 2grand for twenty minutes then open up a bag of pita bread and dig in.
No really, ask the guys who you got it from but generally run it 2 grand for 20 minutes is par for most motors.
I alway run them like I stole em lol.
lol. Oddly enough a lot of guys were recommending this method. Granted they were talking about truck diesels but they said after a swap, load it up and head for the hills. Seemed strange to me. The common theme from most people seemed to be don't run it if it's not under load.
Important stuff Blakes: Get ahold of those people who you got that motor from and ask for specifications about the break in. Grab a work order and put todays date on it, write: fill crankcase with proper oil ( and write what that proper oil is and how much), write all that sort of stuff down on a work order and date it. The more words the better.
Write about how you changed all the filters and made sure everything was golden. Write down how you went with the manufactuers recomended break in proceedure, write down how you made sure clutch/ belt tension is within specification ( that's a big one). Write it good like: Installed drive belts, checked for proper tension, proper tension is so and so.
Think about how they may catch you on warranty cause if they need to they will.
I would say if you head down to the parts house( pep boys should have something) they would have a book on Cummins engines, for 20 bucks you should buy it for reference to the things I mentioned.
When my chipper was still under warranty I used the oil they said to use.
Thanks bud. The block came with oil and filters already on it from the shop's test run so I shouldn't have to worry much about that. I gotta go over the warranty paperwork tomorrow and see if anything pops out. I'm still waiting on new hoses and belts to arrive so I'll have some time to sort it all out. I've already got a file started on this project so adding a few more pieces of paper documenting my work shouldn't be an issue. I took pics of the process as well as our machine's current hours so that should help if something goes wrong. Thanks for the advice.
Yeah it looks like you got the works with that motor. New injection pump? Wowsers! They probably want that oil changed in 100 hours.
Enter your email address to join: