The made in north america Old Magnesium Swap Meet.

[Bill G]

.........................

I'm looking for a Mall 10 or 11 project. If it's a parts saw, complete froze-up yard ornament, or a runner- any is fine.
I don't need the bar, chain, or helper handle.

I have those

 

[Bill G]

I'll ask again....


Looking for a Homelite 410 project or runner, got trades or dollars...

Chris

I have a 410 but it is quite a project

 

[promac850]

Looking for a Pioneer 600 series coil... that is if RandyMac's NU-17 offering don't make no sparky.

 

[RandyMac]

is this missing the clutch cover? what model type?

Never had a clutch cover, it has the 77cc AH47.

 

[apse]

Some Trading Material....

 

[jerrycmorrow]

Never had a clutch cover, it has the 77cc AH47.

looks real similar to the sears d49. is it made by roper?

 

[jerrycmorrow]

ya think?

 

[apse]

 

[promac850]

apse, I just dropped a load in me skivvies... :jawdrop:

You got some gold in there.


pm sent...

 

[eiklj]

Im pretty excited about having an almost 5 cube saw...4.91 is close enough right? lol Ive already started looking for parts to replace the corroded ones...Can you say cart before the horse?

There's some C-7 parts on febay right now, a little high priced IMO.

 

[AU_K2500]

There's some C-7 parts on febay right now, a little high priced IMO.

Ive seen those....didnt know if that was the going rate or not, figured i could do better on here.

 

[AU_K2500]

I've got a spare lower rear handle brace and flywheel cover (both blue parts from a C-5) that you can have for shipping costs. I already gave away my last spare C-series fuel tank. I'm keeping the engine from that parts saw (piston/rings/cylinder/rod/crank/crankcase/crankcase cover) intact as a spare. It's in better shape (internally) than my pretty runner (avatar pic).

You may or may not be able to save the fuel tank on that saw. Looks like it's got some bad corrosion on the bottom. You'll have to carefully remove all that corrosion and see if there's still sound metal underneath. You could then fill the corroded area with JB weld and paint the tank. That's IF the corrosion hasn't gone alll the way through...

PM good as sent

 

[roncoinc]

Ron, I can use the front handle. Busmech was looking for a starter assembly for a 707, yours looks the same as my 707.

I need PM's or i cant keep track of anything
then it's on to email and i can catagorize and keep track with pix and such.

707,i think mine is a 7-19 ..

will have to dig out more of the old stuff and take pix.

got a C-5 carcase with some usable stuff on it also,not much left but some.

 

[RandyMac]

looks real similar to the sears d49. is it made by roper?

Model Profile: SIX 45

 

[67L36Driver]

Now you got my attention.

Wards/Remington SL-4 or PL-4??? The fuel & oil caps says SL-4.

What's the story on it? Needing a carb. box lid?

 

[roncoinc]

Somebody asked me about the C5 parts so i took some pix in the dark..

 

[RandyMac]

Looking for a Pioneer 600 series coil... that is if RandyMac's NU-17 offering don't make no sparky.

I don't remember if it has spark or not, I do know the primer system turned to tar.

 

[promac850]

I don't remember if it has spark or not, I do know the primer system turned to tar.

Well, in that case, you gonna test it for spark or send a price in a pm that you think we can be happy with?

To test for spark, all you gotta do is hold the end of the plug wire while Annie pulls it over. Can't possibly be that hard...

 

[RandyMac]

Well, in that case, you gonna test it for spark or send a price in a pm that you think we can be happy with?

To test for spark, all you gotta do is hold the end of the plug wire while Annie pulls it over. Can't possibly be that hard...

$500.00 local pick-up only.



















LOL, I'll get back to you

 

[Modifiedmark]

Ok, looking for a Poulan 252A, or 744.

Not asking for much.